cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
733
Views
0
Helpful
10
Replies

.323 gateway and CUCM call hand up delay and call s

ausjustin
Level 1
Level 1

I've got a very vexing issue.  I converted a router over from MGCP to h.323.  IOS Advanced IP Services 152.4M6  With MGCP to H323

there was never an issue :

1.       Intermittent call drop outs

2.       Inbound calls call hang up / call termination / end call delay issue around 30 second delay 
 
 
Thanks 
Justin 
10 Replies 10

Hi Justin.

Can you please send us the actual config of your H323 VG?

 

Thanks

 

Regards

 

Carlo

Please rate all helpful posts "The more you help the more you learn"

Thanks 

Attached 

Hi Justin.

Thanks for the configuration.

Can you also please send a show controller E1 and a debug isdn q931 during an incoming call with a termination delay?

 

Thanks

 

Regards

 

Carlo

Please rate all helpful posts "The more you help the more you learn"

Thanks Carlo 

 

PBX-3925-02#
Sep  3 09:47:54.537: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8  callref = 0x00FC 
        Sending Complete 
        Bearer Capability i = 0x8090A3 
                Standard = CCITT 
                Transfer Capability = Speech  
                Transfer Mode = Circuit 
                Transfer Rate = 64 kbit/s 
        Channel ID i = 0xA18382 
                Preferred, Channel 2 
        Calling Party Number i = 0x2183, '63451244' 
                Plan:ISDN, Type:National 
        Called Party Number i = 0xC1, '94556667' 
                Plan:ISDN, Type:Subscriber(local)
Sep  3 09:47:54.537: ISDN Se0/0/0:15 Q931: Received SETUP  callref = 0x80FC callID = 0x099F switch = primary-net5 interface = User 
PBX-3925-02#
Sep  3 09:47:54.541: ISDN Se0/0/0:15 Q931: TX -> CALL_PROC pd = 8  callref = 0x80FC 
        Channel ID i = 0xA98382 
                Exclusive, Channel 2
Sep  3 09:47:54.757: ISDN Se0/0/0:15 Q931: TX -> ALERTING pd = 8  callref = 0x80FC
PBX-3925-02#
Sep  3 09:47:55.781: ISDN Se0/0/0:15 Q931: TX -> CONNECT pd = 8  callref = 0x80FC
Sep  3 09:47:55.797: ISDN Se0/0/0:15 Q931: RX <- CONNECT_ACK pd = 8  callref = 0x00FC
PBX-3925-02#
Sep  3 09:48:03.245: ISDN Se0/0/0:15 Q931: RX <- PROGRESS pd = 8  callref = 0x9151 
        Cause i = 0x8A9F - Normal, unspecified 
        Progress Ind i = 0x8488 - In-band info or appropriate now available 
PBX-3925-02#
Sep  3 09:48:08.921: ISDN Se0/0/0:15 Q931: RX <- DISCONNECT pd = 8  callref = 0x00FA 
        Cause i = 0x8090 - Normal call clearing 
        Progress Ind i = 0x8288 - In-band info or appropriate now available 
Sep  3 09:48:08.921: ISDN Se0/0/0:15 Q931: call_disc: PI received in disconnect; Postpone sending RELEASE for callid 0x99D

Hi Justin.

From this debug I can see that the call has been disconnected immediately.

Can you confirm it?

please also add these to commands in your config

voice call disc-pi-off

voice call convert-discpi-to-prog

 

Let me know

 

 

Regards

 

Carlo

 

 

Please rate all helpful posts "The more you help the more you learn"

I already add on  voice call disc-pi-off .

but what's the "voice call convert-discpi-to-prog"  for ? 

and also do you think we remove the " service mcid" will help ?

 

 

dial-peer voice 1 pots
 description **** Inbound Calls****
 service mcid
 incoming called-number .
 direct-inward-dial
 port 0/0/0:15

HI Justin

That could help

Regarding voice call convert-discpi-to-prog is to change the diconnect message to progress in order to try to send the call status to the CUCM when a disconnect arrives from PSTN

 

 

HTH

 

Regards

 

Carlo

Please rate all helpful posts "The more you help the more you learn"

thanks a lot . 

 

and also maybe I will try change this above timer  "param mcid-release-timer" to 10 seconds instead of 30seconds and then see whether now the calls disconnect after 10seconds, which confirms that the issue is with MCID.

Yes.

Also try that and pleas let me know

 

Regards

 

Carlo

Please rate all helpful posts "The more you help the more you learn"