BE6000s Trunk.

[fisher]

I have a new BE6000S box, and I'm pretty new to cisco voip product.

Right now, I have setup the internal environment and it works fine. However, I want to configure a trunk to make some outbound test calls and I really have no idea about how to configure the voice gateway to connect to the ITSP, anyone have successfully configured this product can give me some tip?

Here is the configuration that i run from the be6000 router/voicegateway.

BE6000S#sh run
Building configuration...


Current configuration : 10858 bytes
!
! Last configuration change at 13:39:58 PST Wed Feb 1 2017 by hanatech
! NVRAM config last updated at 13:00:59 PST Wed Feb 1 2017 by hanatech
!
version 15.5
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
service compress-config
service sequence-numbers
!
hostname BE6000S
!
boot-start-marker
boot-end-marker
!
!
card type e1 0 0
logging buffered 51200 warnings
enable password ************
!
aaa new-model
!
!
aaa authentication login default local
!
!
!
!
!
aaa session-id common
ethernet lmi ce
clock timezone PST -8 0
clock summer-time PDT recurring
network-clock-participate wic 0
!
!
!
!
!
!
!
!
!
ip dhcp excluded-address 172.27.199.1 172.27.199.31
!
ip dhcp pool BE6000S-Preconfigured-S1
 import all
 network 172.27.199.0 255.255.255.192
 default-router 172.27.199.1
 option 150 ip 172.27.199.11
 dns-server 172.27.199.1
 domain-name ciscolocal.com
 lease 0 2
!
!
!
ip domain name ciscolocal.com
ip host ucn1.ciscolocal.com 172.27.199.12
ip host plm.ciscolocal.com 172.27.199.11
ip host pcp.ciscolocal.com 172.27.199.10
ip host s1-cimc1.ciscolocal.com 172.27.199.2
ip host ns.ciscolocal.com 172.27.199.1
ip host s1-esxi1.ciscolocal.com 172.27.199.4
ip host ntp.ciscolocal.com 172.27.199.1
ip host ucm-pub.ciscolocal.com 172.27.199.11 2001::172:27:199:11
ip host imp1.ciscolocal.com 172.27.199.13
ip host s1-dgw.ciscolocal.com 172.27.199.1
ip host s1-ns.ciscolocal.com 172.27.199.1
ip host s1-vgw.ciscolocal.com 172.27.199.1
ip host s1-ntp.ciscolocal.com 172.27.199.1
ip host _cisco-uds._tcp.ciscolocal.com srv 0 1 8443 ucm-pub.ciscolocal.com
ip host _cuplogin._tcp.ciscolocal.com srv 0 1 8443 imp1.ciscolocal.com
ip multicast-routing
ip cef
no ipv6 cef
multilink bundle-name authenticated
!
!
!
!
isdn switch-type primary-net5
!
!
trunk group ALL_PSTN
!
!
crypto pki trustpoint TP-self-signed-2314118582
 enrollment selfsigned
 subject-name cn=IOS-Self-Signed-Certificate-2314118582
 revocation-check none
 rsakeypair TP-self-signed-2314118582
!
!
crypto pki certificate chain TP-self-signed-2314118582
 certificate self-signed 01
  3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
  31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
  69666963 6174652D 32333134 31313835 3832301E 170D3137 30313133 31353436
  35305A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
  4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D32 33313431
  31383538 3230819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
  8100B612 E922C5C9 DE006D62 A9AC7722 181649FC 3552A5A1 31011847 8DF7173B
  70AC839F 50458C88 0A1AF43E 29DDBA2A AFAEA88C 46FE6E03 63344C0D 48948982
  837AC0F6 0B21F37D E3792FA7 96BE44AA 86875FAD 89D3F2F6 DAE525C5 9490DF81
  1ED585ED 22ECC19E 4B353BC7 100148EA 16D87AFC 4C6239FA F10914F9 E4F5E1A2
  83E30203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603
  551D2304 18301680 1440C6EE F4354019 592FD4C1 AA9065A6 FAC1572C A5301D06
  03551D0E 04160414 40C6EEF4 35401959 2FD4C1AA 9065A6FA C1572CA5 300D0609
  2A864886 F70D0101 05050003 818100A4 0D38E9FD B6D58399 243B60E6 4FE45C3B
  A272F64B 97184034 560706BB F36A5004 783B53FB D9A06C78 4656D40F EEEAC5BC
  A3451251 42F70EBD DBFF9B71 660E1C5F 4ABB8C00 FF82B85C 19D5D9DD 1CDC6C10
  D8274864 D782700D F0A56CE5 17CC9A39 79AE1FF8 AF171A59 1C92D9BF F6AB088B
  23F958B9 B0ED7290 5E86C25D 8029FA
        quit
voice-card 0
!
!
!
voice service voip
 ip address trusted list
  ipv4 172.27.199.11
  ipv4 172.27.199.14
  ipv4 172.27.199.15
 no supplementary-service sip moved-temporarily
 no supplementary-service sip refer
 no supplementary-service sip handle-replaces
 fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
 no fax-relay sg3-to-g3
 modem passthrough nse codec g711ulaw
 sip
  bind control source-interface BVI1
  bind media source-interface BVI1
  asymmetric payload full
  no update-callerid
!
!
voice class uri ucm sip
 host ^172.27.199.1[145]$
voice class codec 1
 codec preference 1 g711ulaw
 codec preference 2 g729r8
 codec preference 3 g711alaw
 codec preference 4 ilbc
!
!
!
!
voice translation-rule 1
!
voice translation-rule 2
 rule 1 /^.*\(...\)$/ /1\1/
!
voice translation-rule 3
 rule 1 /^.\(...\)$/ /5551234\1/ type any national plan any isdn
!
voice translation-rule 4
 rule 1 /^\+1\(...\)/ /\1/ type any national plan any isdn
 rule 2 /^\+1\(.*\)/ /1\1/ type any national plan any isdn
 rule 3 /^\+\(.*\)/ /011\1/ type any international plan any isdn
!
!
voice translation-profile PSTN-to-UCM
translate calling 1
translate called 2
!
voice translation-profile UCM-to-PSTN
translate calling 3
translate called 4
!
!
!
fax interface-type fax-mail
license udi pid CISCO2921/K9 sn FJC2102A1G5
hw-module pvdm 0/0
!
hw-module sm 1
!
!
!
archive
 log config
  logging enable
  logging size 600
  hidekeys

!
redundancy
!
!
controller E1 0/0/0
 pri-group timeslots 1-31
 description Primary Rate Connection to PSTN
!
bridge irb
!
!
!
!
interface Embedded-Service-Engine0/0
 no ip address
 ip broadcast-address 0.0.0.0
!
interface GigabitEthernet0/0
 description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$
 ip address dhcp
 ip pim sparse-dense-mode
 ip igmp version 3
 duplex auto
 speed auto
!
interface GigabitEthernet0/1
 no ip address
 ip broadcast-address 0.0.0.0
 duplex auto
 speed auto
 bridge-group 1
!
interface GigabitEthernet0/2
 no ip address
 ip broadcast-address 0.0.0.0
 duplex auto
 speed auto
!
interface Serial0/0/0:15
 no ip address
 ip broadcast-address 0.0.0.0
 encapsulation hdlc
 isdn switch-type primary-net5
 isdn incoming-voice voice
 isdn sending-complete
 isdn outgoing display-ie
 trunk-group ALL_PSTN
 no cdp enable
!
interface ucse1/0
 description Internal interface connected to UCSE Port 0
 ip unnumbered BVI1
 ip broadcast-address 0.0.0.0
 service-module heartbeat-reset disable
 imc ip address 172.27.199.2 255.255.255.192 default-gateway 172.27.199.1
 imc access-port shared-lom console
 bridge-group 1
!
interface ucse1/1
 description Internal switch interface connected to UCSE Port 1
 no ip address
!
interface Vlan1
 no ip address
 ip broadcast-address 0.0.0.0
!
interface BVI1
 description Bridge interface providing access to router and UCSE module.
 ip address 172.27.199.5 255.255.255.192 secondary
 ip address 172.27.199.1 255.255.255.192
 ip broadcast-address 172.27.199.0
 ip pim sparse-dense-mode
 ip igmp version 3
!
ip forward-protocol nd
!
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
!
ip dns server
ip route 0.0.0.0 0.0.0.0 192.168.1.1
!
!
!
snmp-server community public RO
access-list 23 permit 10.0.0.0 0.255.255.255
access-list 23 permit 172.16.0.0 0.15.255.255
access-list 23 permit 192.168.0.0 0.0.255.255
!
!
!
control-plane
!
bridge 1 protocol ieee
bridge 1 route ip
!
voice-port 0/0/0:15
 !
 !
 !
 !
!
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
!
mgcp profile default
!
!
!
!
dial-peer voice 1 pots
 trunkgroup ALL_PSTN
 description Default inbound dial-peer for calls from PSTN
 translation-profile incoming PSTN-to-UCM
 incoming called-number .
 direct-inward-dial
!
dial-peer voice 50 voip
 description Inbound voip dial-peer for calls from UCM
 session protocol sipv2
 incoming uri from ucm
 voice-class codec 1
 dtmf-relay sip-kpml rtp-nte
 no vad
!
dial-peer voice 100 pots
 trunkgroup ALL_PSTN
 description E.164 calls from UCM to PSTN
 translation-profile outgoing UCM-to-PSTN
 destination-pattern +.+
 forward-digits all
 no sip-register
!
dial-peer voice 200 voip
 description Calls from PSTN to UCM
 destination-pattern 1...
 session protocol sipv2
 session target ipv4:172.27.199.11
 voice-class codec 1
 dtmf-relay sip-kpml rtp-nte
 no vad
!
!
sip-ua

 timers trying 100
 
!
!
!
gatekeeper
 shutdown
!
!
banner exec ^C
-----------------------------------------------------------------------------
                        Cisco Business Edition 6000S

You must create a new user name and password using Cisco CP or the following
CLI command before continuing to use this system:

username <newusername> privilege 15 secret <newpassword>

WARNING: This system includes a Cisco UCS server module which MUST be shut
down (power button is orange) before removing power.  Failure to shut down
gracefully may result in data loss or corruption.

For further information, refer to the BE6000S installation guide:
www.cisco.com/go/be6ksig
-----------------------------------------------------------------------------
^C
banner login ^C
-----------------------------------------------------------------------------
                        Cisco Business Edition 6000S

This appliance has been preconfigured for your convenience.  You may manage
this system locally via console, or by connecting to 172.27.199.1 through
interface GigabitEthernet 0/1 using Telnet, SSH or Cisco Configuration
Professional (Cisco CP) via HTTP. DHCP is enabled for client configuration.

For initial access, log in with user name "admin" and password "password".
These credentials may be used for the first log in ONLY.  If you log out
without creating a new user name, you may not be able to log in again.

WARNING: This system includes a Cisco UCS server module which MUST be shut
down (power button is orange) before removing power.  Failure to shut down
gracefully may result in data loss or corruption.

For further information, refer to the BE6000S installation guide:
www.cisco.com/go/be6ksig
-----------------------------------------------------------------------------
^C
!
line con 0
 exec-timeout 0 0
 privilege level 15
line aux 0
line 2
 no activation-character
 no exec
 transport preferred none
 transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
 stopbits 1
line 67
 no activation-character
 no exec
 transport preferred none
 transport input all
 transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
 stopbits 1
 speed 9600
 flowcontrol software
line vty 0 4
 exec-timeout 0 0
 privilege level 15
 transport input telnet ssh
line vty 5 15
 exec-timeout 0 0
 privilege level 15
 transport input telnet ssh
line vty 16 1114
 exec-timeout 0 0
 transport input none
!
scheduler allocate 20000 1000
ntp master 3
ntp update-calendar
ntp server 0.ciscosb.pool.ntp.org
ntp server 3.ciscosb.pool.ntp.org
ntp server 1.ciscosb.pool.ntp.org
ntp server 2.ciscosb.pool.ntp.org
!
end