We are setting up a 10 channel E1 R2 in Brasilia. Its currently working perfectly with a PBX, we are moving it to CME with 2811
We are in the testing stage, I am testing it remotely from Europe which isnt ideal.
Currently, the E1 comes up and inbound calls ring ok - after a delay. However once you pickup the phone all you hear is a loud tone and no voice.
Any help appreciated - please see configuration / debug below and attached debug file.
Im not sure what to change.
Regards
James
!
2811 / ADV Ipservices / 12.4 (24)T8 / VWIC-2MFT-E1=
Current Configuration
!
controller E1 0/0/0
framing NO-CRC4
clock source line primary
ds0-group 1 timeslots 1-10 type r2-digital r2-non-compelled ani
cas-custom 1
country brazil
metering
double-answer
category 2
answer-signal group-b 1
!
voice-port 0/0/0:1
no echo-cancel enable
cptone BR
!
sho voice call summary
PORT CODEC VAD VTSP STATE VPM STATE
============== ========= === ==================== ======================
0/0/0:1.1 - - - R2_Q421_IDLE
0/0/0:1.2 - - - R2_Q421_IDLE
0/0/0:1.3 - - - R2_Q421_IDLE
0/0/0:1.4 - - - R2_Q421_IDLE
0/0/0:1.5 - - - R2_Q421_IDLE
0/0/0:1.6 - - - R2_Q421_IDLE
0/0/0:1.7 - - - R2_Q421_IDLE
0/0/0:1.8 - - - R2_Q421_IDLE
0/0/0:1.9 - - - R2_Q421_IDLE
0/0/0:1.10 - - - R2_Q421_IDLE
0/1/0 - - - FXSLS_PARK
0/1/1 - - - FXSLS_PARK
sho voice port summary
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
=============== == ============ ===== ==== ======== ======== ==
0/0/0:1 01 r2-digital up dorm idle idle n
0/0/0:1 02 r2-digital up dorm idle idle n
0/0/0:1 03 r2-digital up dorm idle idle n
0/0/0:1 04 r2-digital up dorm idle idle n
0/0/0:1 05 r2-digital up dorm idle idle n
0/0/0:1 06 r2-digital up dorm idle idle n
0/0/0:1 07 r2-digital up dorm idle idle n
0/0/0:1 08 r2-digital up dorm idle idle n
0/0/0:1 09 r2-digital up dorm idle idle n
0/0/0:1 10 r2-digital up dorm idle idle n
0/1/0 -- fxs-ls up up off-hook idle y
0/1/1 -- fxs-ls up up off-hook idle y
sho voice port
R2 Slot is 0, Subslot is 0, Sub-unit is 0, Port is 1
Type of VoicePort is R2
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 0 dB
Echo Cancellation is disabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 128 ms
Echo Cancel worst case ERL is set to 6 dB
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 1000 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 15 s
Interdigit Time Out is set to 10 s
Call Disconnect Time Out is set to 60 s
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 30 s
Companding Type is A-law
Rx A bit no conditioning set
Rx B bit no conditioning set
Rx C bit no conditioning set
Rx D bit no conditioning set
Tx A bit no conditioning set
Tx B bit no conditioning set
Tx C bit no conditioning set
Tx D bit no conditioning set
Region Tone is set for BR
Station name None, Station number None
Translation profile (Incoming):
Translation profile (Outgoing):
Voice card specific Info Follows:
Line Signalling Type is r2-digital
Register Signalling Type is r2-non-compelled
Country setting is brazil
Answer Signal is group-b 1
Category is set to 2
NC Congestion is set to 4
KA is set to 0
KD is set to 0
Caller Digits is set to 1
Request Category is set to 0
End of DNIS is set to False
DNIS Digits min is 0 and max is 0
ANI Digits min is 0 and max is 0
Group A Callerid End is set to False
Metering is on
Release Ack is set to False
Unused ABCD Bits Mask configured: 0 0 0 0
Inverting ABCD Bits Mask configured: 0 0 0 0
Debounce Time is set to 40ms
Release Guard Time is set to 2000ms
Seizure Ack Time is set to 100ms
Answer Guard Time is set to 0ms
ANI Timeout is set to 0s
DS0 channel specific status info:
IN OUT
PORT CH SIG-TYPE OPER STATUS STATUS TIP RING
=============== == ============ ==== ====== ====== === ====
0/0/0:1 01 r2-digital dorm idle idle
0/0/0:1 02 r2-digital dorm idle idle
0/0/0:1 03 r2-digital dorm idle idle
0/0/0:1 04 r2-digital dorm idle idle
0/0/0:1 05 r2-digital dorm idle idle
0/0/0:1 06 r2-digital dorm idle idle
0/0/0:1 07 r2-digital dorm idle idle
0/0/0:1 08 r2-digital dorm idle idle
0/0/0:1 09 r2-digital dorm idle idle
0/0/0:1 10 r2-digital dorm idle idle
show controllers e1
E1 0/0/0 is up.
Applique type is Channelized E1 - balanced
No alarms detected.
alarm-trigger is not set
Version info Firmware: 20090113, FPGA: 20, spm_count = 0
Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line Primary.
Data in current interval (436 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Total Data (last 24 hours)
842 Line Code Violations, 2754 Path Code Violations,
11 Slip Secs, 2 Fr Loss Secs, 23 Line Err Secs, 0 Degraded Mins,
1 Errored Secs, 0 Bursty Err Secs, 24 Severely Err Secs, 30815 Unavail Secs
Brasilia-2811-VOIP#sho voice register all
VOICE REGISTER GLOBAL
=====================
CONFIG [Version=7.1]
========================
Version 7.1
Mode is srst
Max-pool is 0
Max-dn is 0
Outbound-proxy is enabled and will use global configured value
timeout interdigit 0
network-locale[0] US (This is the default network locale for this box)
network-locale[1] US
network-locale[2] US
network-locale[3] US
network-locale[4] US
user-locale[0] US (This is the default user locale for this box)
user-locale[1] US
user-locale[2] US
user-locale[3] US
user-locale[4] US
VOICE REGISTER DN
=================
VOICE REGISTER POOL
===================
