08-04-2015 05:06 AM - edited 03-17-2019 03:52 AM
I have bought 2 Cisco 8831 Phones but not is possible keep more of 2 calls. In other words not is possible keep a multiconference. I have configured the Directory Number to permit a maximum of calls 6, but still not works.
08-04-2015 12:27 PM
The number of people you can have in a conference is not related to the maximum number of calls a phone can have, that's set in your CFB and if using CUCM, the conference related parameters.
09-06-2015 05:52 AM
Hi,
I have seen that on the router gateway is not configured the DSPfarm and this feature is necessary to conferencing. I have seen that the common configuration is create with DSPfarm profile and associated SCCP with DSPfarm like this:
sccp local GigabitEthernet0/0
sccp ccm 10.126.71.21 identifier 101 version 4.1
sccp ccm 10.126.222.21 identifier 102 version 4.1
sccp ip precedence 3
sccp
!
sccp ccm group 121
associate profile 133 register MTP_HW_UKBI_R8
associate profile 132 register MTP_HW_UKBI_AL
associate profile 131 register MTP_HW_UKBI_UL
associate profile 111 register CFB_HW_UKBI01
associate profile 121 register XCODE_HW_UKBI01
!
dspfarm profile 121 transcode
description Birmingham Hardware transcoder
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec pass-through
maximum sessions 4
associate application SCCP
!
dspfarm profile 111 conference
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
associate application SCCP
!
dspfarm profile 131 mtp
codec g711ulaw
codec pass-through
maximum sessions hardware 4
associate application SCCP
!
dspfarm profile 132 mtp
codec g711ulaw
codec pass-through
maximum sessions hardware 4
associate application SCCP
!
dspfarm profile 133 mtp
codec g711ulaw
codec pass-through
maximum sessions hardware 4
associate application SCCP
!
But in my case the difference is the Cisco Spider 8831 is working with the SIP protocol instead of SCCP (by default). I need to know if the configuration on Router gateway is different...
Thanks in advance!
09-06-2015 07:46 AM
DSPfarms can only be handled via SCCP, that has nothing to do with whether you have a SIP trunk, H.323 or MGCP for TDM/SIP trunks or CUCM.
09-07-2015 12:50 PM
OK,
However I want to Associating a DSP Farm Profile to a Cisco Unified Communications Manager Group. For this I need to create register device-name. But i don't know how create this register on the callmanager.
Router(config-sccp-ccm)# associate profile register abgz12345
Thanks,
09-07-2015 01:00 PM
There's plenty of material on the topic on cisco.com if you simply search.
08-04-2015 01:57 PM
Just adding a bit to Jaime's correct response: The maximum number of audio streams your UCM can handle at a time is 128. This includes ad-hoc and meetme.
You configure the maximum ad-hoc participants under the service parameter called "Maximum Ad Hoc Conference". Keep in mind not to make this number too high, since each time you use the software conference bridge it'll provision for the maximum number of participants. So if you put the maximum (64), a conference of 3 will still provision 64 out of a possible 128 your CUCM can provide.
An excellent source on the subject of conference bridging is:
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/admin/10_0_1/ccmsys/CUCM_BK_SE5FCFB6_00_cucm-system-guide-100/CUCM_BK_SE5FCFB6_00_cucm-system-guide-100_chapter_011000.html
08-05-2015 03:29 AM
08-06-2015 03:05 AM
On the 8831 phone appear: "conf list is not active". I think that is necessary to add new configuration on the gateway because theses phones are working as SIP protocol.
Thanks,
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide