03-16-2016 06:56 PM - edited 03-17-2019 06:16 AM
Hi Cisco Techs,
Cisco Voice network module NM-2V uses various IOS's including 12.3(2) T for a 2691 router (see chart below) from link....
The following table details the NM-1V and NM-2V platform support.
Cisco IOS Support | VG200 | 2600 | 2600XM/ 2650XM | 2691 | 3620, 3640 | 3660 | 3725/3745 |
---|---|---|---|---|---|---|---|
NM-1V | 12.1(1)XE, 12.1(3)T, 12.1(5)XM, 12.2(1), 12.2(2)T, 12.3(1) | 11.3(2)XA, 11.3(3)T, 12.0(1)T, 12.0(1), 12.0(3)T, 12.0(5)XK, 12.0(7)T, 12.1(1)T, 12.1(1), 12.1(5)YB, 12.1(5)YD, 12.2(1), 12.2(2)T, 12.2(2)XT, 12.2(11)YT, 12.3(1) | 12.1(14), 12.2(8)T1, 12.2(11)T, 12.2(11)YT, 12.2(12), 12.2(15)ZJ, 12.3(1), 12.3(2)T | 12.2(8)T1, 12.2(11)YT, 12.2(15)ZJ, 12.3(1), 12.3(2)T | 11.3(1)T, 12.0(1)T, 12.0(1), 12.0(2)T, 12.0(2)XC, 12.0(2)XD, 12.0(3)T, 12.0(5)XK, 12.0(7)T, 12.0(7)XK, 12.1(1)T, 12.1(1), 12.1(5)YB, 12.1(5)YD, 12.2(1), 12.2(2)T, 12.2(2)XT, 12.2(11)YT, 12.2(15)ZJ, 12.3(1) | 12.0(5)T, 12.0(5)XK, 12.0(7)XK, 12.1(1)T, 12.1(1), 12.1(5)YB, 12.1(5)YD, 12.2(1), 12.2(2)T, 12.2(2)XT, 12.2(8)T, 12.2(11)YT, 12.2(15)ZJ, 12.3(1), 12.3(2)T | 12.2(8)T1, 12.2(11)YT, 12.2(15)ZJ, 12.3(1), 12.3(2)T |
NM-2V | 12.1(3)T 12.1(5)XM, 12.2(1), 12.2(2)T, 12.3(1) | 11.3(2)XA, 11.3(3)T, 12.0(1)T, 12.0(1), 12.0(3)T, 12.1(1)T, 12.1(1), 12.1(5)YB, 12.1(5)YD, 12.2(1), 12.2(2)T, 12.2(2)XT, 12.2(11)YT, 12.3(1) | 12.1(14), 12.2(8)T1, 12.2(11)T, 12.2(11)YT, 12.2(12), 12.2(15)ZJ, 12.3(1), 12.3(2)T | 12.2(8)T1, 12.2(11)YT, 12.2(15)ZJ, 12.3(1), 12.3(2)T | 11.3(1)T, 12.0(1)T, 12.0(1), 12.0(2)T, 12.0(2)XC, 12.0(2)XD, 12.0(3)T, 12.0(5)XK, 12.0(7)T, 12.0(7)XK, 12.1(1)T, 12.1(1), 12.1(5)YB, 12.1(5)YD, 12.2(1), 12.2(2)T, 12.2(2)XT, 12.2(11)YT, 12.2(15)ZJ, 12.3(1) | 12.0(5)T, 12.0(5)XK, 12.0(7)XK, 12.1(1)T, 12.1(1), 12.1(5)YB, 12.1(5)YD, 12.2(1), 12.2(2)T, 12.3(1), 12.3(2)T | 12.2(8)T1, 12.2(11)YT, 12.2(15)ZJ, 12.3(1), 12.3(2)T |
However. The IOS I have is 12.4(25d) on my router.
Even though there is only .1 of a difference (.3) to the (.4)in the train number.
Does that really matter please?
Thanks again
03-17-2016 07:11 AM
It is highly likely to support that module.
03-17-2016 02:31 PM
Hi Philip,
Thanks for your response.
Is there a link I can use/follow to assist in configuring this network module please?
03-17-2016 09:30 PM
It can do quite a lot of things. What did you want it to do, and then I might be able to dig up an example.
03-17-2016 09:32 PM
Thanks for the response.
Configure NM-2V in the router please. Is already in the device. As I have a VIC BRI in this.
03-17-2016 09:35 PM
Configure it to do what? Work with call manager, work with CME, act as a conference bridge, H.323 routing, what do you want to use it for?
03-17-2016 10:14 PM
Sorry. To work with call manager using SIP to ISP for outgoing calls..
I have a separate device (DID) for incoming calls
03-19-2016 01:12 AM
Hi Philip,
Thanks for the previous reply.
I will be using ISDN modem to ISP via a BRI VIC interface that sits in NM-2V
Sorry if you didn't get this before. Thought I sent it
03-20-2016 12:20 PM
This will get you started,
http://www.cisco.com/c/en/us/support/docs/voice/digital-ccs/15415-bri-voice-port-cfg.html
And the general reference for sip:
http://www.cisco.com/c/en/us/td/docs/ios/12_2/voice/configuration/guide/fvvfax_c/vvfsip.html
03-20-2016 05:01 PM
Thanks Philip.
Much appreciated again :)
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide