05-21-2015 02:01 PM - edited 03-17-2019 03:05 AM
Hello people,
I´m trying to configure a environment with COR List and Extension Mobility using SIP Devices.
I know that this configuration is possible, and easy in SCCP Phones, because we configure the COR list in the Lines (ephone-dn).
About the SIP Devices, Such the cor list is configured in SIP Device, when I use the Extension Mobility I can not change the cor list (after logged in).
The idea is, when the Device is logged out, appear the DN 2011. After the login, the DN will be 2012.
When is logged out (2011), I can not make calls to mobile phone.
When is logged in (2012), I can make calls to mobile phone.
Is it possible??
Thank you!!
Bruno
voice register global
mode cme
source-address 192.168.15.1 port 5060
max-dn 30
max-pool 30
load 8961 sip8961.9-2-2SR1-9.loads
timezone 17
time-format 24
date-format D/M/Y
url authentication http://192.168.15.1/CCMCIP/authenticate.asp name pass
tftp-path flash:
file text
create profile sync 0002713292036859
ntp-server 192.168.15.1 mode directedbroadcast
camera
video
!
voice register dn 1
number 2011
allow watch
pickup-group 1
name Bruno Falco - Logged Out
label Bruno Falco - Logged Out
!
voice register dn 2
number 2012
allow watch
pickup-group 1
name Bruno Falco - Logged In
label Bruno Falco - Logged In
!
voice register pool 1
logout-profile 2
id mac DCA5.F487.5ACC
type 8961
cor incoming CSS-Mobile default
codec g711ulaw
!
voice logout-profile 2
pin 12345
user 2011 password 12345
number 2011 type normal
speed-dial 1 1111 label "SIP Logged Out"
!
voice user-profile 2
pin 666666
user bfl password 12345
number 2012 type normal
speed-dial 1 2001 label "Logged In"
!
dial-peer cor custom
name Local
name Mobile
name DDI
!
dial-peer cor list CSS-Local
member Local
!
dial-peer cor list CSS-Mobile
member Local
member Mobile
!
dial-peer cor list CSS-DDI
member Local
member Mobile
member DDI
!
dial-peer cor list PT-Local
member Local
!
dial-peer cor list PT-Mobile
member Mobile
!
dial-peer cor list PT-DDI
member DDI
!
dial-peer voice 10 voip
corlist outgoing PT-Mobile
description Calls to Mobile
destination-pattern 9........
session protocol sipv2
session target ipv4:192.168.1.3
session transport tcp
voice-class codec 1
dtmf-relay rtp-nte
no vad
!
Solved! Go to Solution.
07-05-2015 02:31 PM
Hi,
I had similar issue few days ago, but I've found a workarounf. Leave COR config as it is, and then configure after hours. Under "telephony-service" configure after hours time, I've set that it is always "after hours" setup. Then you need to set which patterns are blocked during that time. In our configuration, we need to allow calls just to emergency services. Here are the commands:
after-hours block pattern 1 02T
after-hours block pattern 2 03T
after-hours block pattern 4 04T
after-hours block pattern 5 05T
after-hours block pattern 6 06T
after-hours block pattern 7 07T
after-hours block pattern 8 08T
after-hours block pattern 9 09T
after-hours block pattern 10 00T
after-hours day Sun 12:00 12:00
after-hours day Mon 12:00 12:00
after-hours day Tue 12:00 12:00
after-hours day Wed 12:00 12:00
after-hours day Thu 12:00 12:00
after-hours day Fri 12:00 12:00
after-hours day Sat 12:00 12:00
This affects all DNs, so you have to add "after-hour exempt" command to "logged-in" DN.
Best Regards,
Nikola
07-05-2015 02:31 PM
Hi,
I had similar issue few days ago, but I've found a workarounf. Leave COR config as it is, and then configure after hours. Under "telephony-service" configure after hours time, I've set that it is always "after hours" setup. Then you need to set which patterns are blocked during that time. In our configuration, we need to allow calls just to emergency services. Here are the commands:
after-hours block pattern 1 02T
after-hours block pattern 2 03T
after-hours block pattern 4 04T
after-hours block pattern 5 05T
after-hours block pattern 6 06T
after-hours block pattern 7 07T
after-hours block pattern 8 08T
after-hours block pattern 9 09T
after-hours block pattern 10 00T
after-hours day Sun 12:00 12:00
after-hours day Mon 12:00 12:00
after-hours day Tue 12:00 12:00
after-hours day Wed 12:00 12:00
after-hours day Thu 12:00 12:00
after-hours day Fri 12:00 12:00
after-hours day Sat 12:00 12:00
This affects all DNs, so you have to add "after-hour exempt" command to "logged-in" DN.
Best Regards,
Nikola
07-06-2015 10:47 AM
Hi Nikola,
Tks for your replay.
I agree with you.
I have needed to use this commands to solve this "issue".
Regards,
Bruno
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide