FXO port calls not going through via LCR (leased cost routing)

abc4308449 · ‎06-03-2015

Morning, Charles

I have another problem I have 2x 4 port FXO cards at one brach all configures are listed below, but when a call is being made via the FXO port listed below calls are not going through I have done all possible traces but with no luck, Please can you help?

Call Manger is : 10.144.56.10

2900 Gateway router is: 10.248.34.102

Show Voice Port Summary:

0/1/0           -- fxo-ls      up    dorm idle     on-hook y
0/1/1           -- fxo-ls      up    dorm idle     on-hook y
0/1/2           -- fxo-ls      up    dorm idle     on-hook y
0/1/3           -- fxo-ls      up    dorm idle     on-hook y
0/2/0           -- fxo-ls      up    dorm idle     on-hook y
0/2/1           -- fxo-ls      up    dorm idle     on-hook y
0/2/2           -- fxo-ls      up    dorm idle     on-hook y
0/2/3           -- fxo-ls      up    dorm idle     on-hook y

'

Below is the routers configure:

!
isdn switch-type primary-net5
!
cts logging verbose
!
!
voice-card 0
dspfarm
dsp services dspfarm
!
!
voice call send-alert
voice call convert-discpi-to-prog always
voice rtp send-recv
voice disc-pi-incoming-on
!
voice service voip
ip address trusted list
ipv4 10.149.250.0 255.255.255.0
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
no supplementary-service sip refer
redirect ip2ip
fax protocol pass-through g711alaw
modem passthrough nse codec g711alaw
h323
call preserve limit-media-detection
sip
session transport tcp
registrar server expires max 600 min 60
!
voice class codec 1
codec preference 1 g729r8
codec preference 2 g711ulaw
!
voice class h323 1
h225 timeout tcp establish 3
!
!
!
!
voice register global
mode srst
timeouts interdigit 5
system message SRST Mode - Limited
max-dn 100
max-pool 110
!
voice register pool 1
id network 10.149.250.0 mask 255.255.255.0
preference 1
proxy 10.248.34.102
dtmf-relay rtp-nte cisco-rtp sip-notify
codec g711ulaw
no vad
!
!
!
voice translation-rule 1
rule 1 /^04850024$/ /82995927/
rule 2 /^.*$....$/ /8198\1/
!
voice translation-rule 2
rule 1 /^8198$4...$$/ /04850024\1/
!
voice translation-rule 3
rule 1 /^4...$/ /8198\0/
rule 2 /^7...$/ /8198\0/
rule 3 /^5927$/ /8299\0/
!
!
voice translation-profile phones-in
translate called 3
!
voice translation-profile pstn-in
translate called 1
!
voice translation-profile pstn-out
translate calling 2
!
!
!
license udi pid CISCO2921/K9 sn FCZ182370YT
hw-module pvdm 0/0
!
hw-module pvdm 0/1
!
!
!
username a privilege 15 password 7 0305
username btsupport password 7 04591F151A315C411B0D44
!
redundancy
!
!
controller E1 0/0/0
framing NO-CRC4
pri-group timeslots 1-31 service mgcp
description PSTN +263 (0)4850024 4000 - 4999
!
controller E1 0/0/1
shutdown
description SPARE - NOT USED
!
ip ftp source-interface Loopback10
ip tftp source-interface Loopback10
ip ssh time-out 60
ip ssh source-interface Loopback10
ip ssh version 2
!
!
!
!
interface Loopback10
description Management and Routing Loopback
ip address 10.248.34.102 255.255.255.255
h323-gateway voip interface
h323-gateway voip bind srcaddr 10.248.34.102
!
interface Embedded-Service-Engine0/0
no ip address
shutdown
!
interface GigabitEthernet0/0
description Zimbabwe, ZW0001 - Harare LAN switch port 23 (VLAN30)[BTM]
ip address 10.149.250.2 255.255.255.0
no ip redirects
no ip unreachables
duplex auto
speed auto
no mop enabled
!
interface GigabitEthernet0/1
description SPARE - NOT USED
no ip address
no ip redirects
no ip unreachables
shutdown
duplex auto
speed auto
no mop enabled
!
interface GigabitEthernet0/2
description SPARE - NOT USED
no ip address
no ip redirects
no ip unreachables
shutdown
duplex auto
speed auto
no mop enabled
!
interface Serial0/0/0:15
description PSTN +263 (0)4850024 4000 - 4999
no ip address
encapsulation hdlc
no snmp trap link-status
isdn switch-type primary-net5
isdn overlap-receiving
isdn incoming-voice voice
isdn bind-l3 ccm-manager
isdn sending-complete
no cdp enable
!
router ospf 1
router-id 10.248.34.102
network 10.149.250.0 0.0.0.255 area 0
network 10.248.34.102 0.0.0.0 area 0
!
ip forward-protocol nd
!
no ip http server
no ip http secure-server
!
ip tacacs source-interface Loopback10
!
logging source-interface Loopback10
logging host 195.218.44.198
logging host 194.102.0.149
!
!
snmp-server community m0R3te4V1cAr RW 15
snmp-server community go1Ngf0Rg0lD RO 15
snmp-server trap-source Loopback10
snmp-server tftp-server-list 15
snmp-server location Zimbabwe - ZW0001 - Harare
snmp-server enable traps snmp linkdown linkup coldstart warmstart
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps config
snmp-server enable traps entity
snmp-server host 172.27.8.36 version 2c aaza-vg-zw0001-01
snmp-server host 172.27.8.37 version 2c aaza-vg-zw0001-01
snmp-server host 172.27.8.43 version 2c aaza-vg-zw0001-01
snmp-server host 172.27.8.44 version 2c aaza-vg-zw0001-01
snmp-server file-transfer access-group 15 protocol tftp
tacacs-server host 199.80.49.10
tacacs-server host 199.80.48.10
tacacs-server timeout 20
tacacs-server directed-request
tacacs-server key 7 06070E74141C5A
access-list 6 deny   any
access-list 7 deny   any
access-list 15 remark ++ Allowed SNMP BT only++
access-list 15 permit 62.239.34.0 0.0.1.255
access-list 15 permit 194.102.6.0 0.0.0.255
access-list 15 permit 194.102.8.0 0.0.1.255
access-list 15 permit 194.102.19.0 0.0.0.255
access-list 15 permit 193.113.254.128 0.0.0.127
access-list 15 permit 193.113.244.128 0.0.0.127
access-list 15 permit 172.27.8.32 0.0.0.31
access-list 99 permit 10.144.0.124
!
!
!
control-plane
!
!
voice-port 0/0/0:15
cptone C1
description PSTN +263 (0)4850024 4000 - 4999
bearer-cap Speech
!
voice-port 0/1/0
cptone C1
timing hookflash-out 50
timing guard-out 1000
description LCR to Mobile (SIM 0772238762)
!
voice-port 0/1/1
cptone C1
timing hookflash-out 50
timing guard-out 1000
description LCR to Mobile (SIM 0772100078)
!
voice-port 0/1/2
cptone C1
timing hookflash-out 50
timing guard-out 1000
description LCR to Mobile (SIM 0772105366 Flty)
!
voice-port 0/1/3
cptone C1
timing hookflash-out 50
timing guard-out 1000
description SPARE - NOT USED
!
voice-port 0/2/0
cptone C1
timing hookflash-out 50
timing guard-out 1000
description LCR to Mobile (SIM 0772238762)
!
voice-port 0/2/1
cptone C1
timing hookflash-out 50
timing guard-out 1000
description LCR to Mobile (SIM 0772238763)
!
voice-port 0/2/2
cptone C1
timing hookflash-out 50
timing guard-out 1000
description LCR to Mobile (SIM 0772105370)
!
voice-port 0/2/3
description SPARE - NOT USED
!
!
!
!
!
mgcp
mgcp call-agent 10.144.56.10 2427 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp package-capability rtp-package
mgcp package-capability sst-package
mgcp package-capability pre-package
no mgcp package-capability res-package
no mgcp package-capability fxr-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp fax t38 inhibit
mgcp rtp payload-type g726r16 static
mgcp bind control source-interface Loopback10
mgcp bind media source-interface Loopback10
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
!
mgcp profile default
!
sccp local Loopback10
sccp ccm 10.144.56.10 identifier 1 version 7.0
sccp ccm 10.144.56.5 identifier 2 version 7.0
sccp
!
sccp ccm group 1
associate ccm 1 priority 1
associate ccm 2 priority 2
associate profile 1 register XCO-HW-ZW0001
associate profile 2 register CFB-HW-ZW0001
associate profile 3 register MTP-HW-ZW0001
keepalive retries 5
switchover method immediate
switchback method immediate
switchback interval 15
!
ccm-manager music-on-hold
!
ccm-manager fallback-mgcp
ccm-manager redundant-host 10.144.56.5
ccm-manager mgcp
no ccm-manager fax protocol cisco
ccm-manager config server 10.144.56.4 10.144.56.8
ccm-manager config
ccm-manager download-tones
!
dspfarm profile 1 transcode
codec g729abr8
codec g729ar8
codec g711alaw
codec g711ulaw
codec g729r8
maximum sessions 10
associate application SCCP
!
dspfarm profile 2 conference
codec g729br8
codec g729r8
codec g729abr8
codec g729ar8
codec g711alaw
codec g711ulaw
maximum sessions 1
associate application SCCP
!
dspfarm profile 3 mtp
codec g711ulaw
maximum sessions software 250
associate application SCCP
!
dial-peer voice 1 pots
description PSTN outbound
translation-profile incoming pstn-in
translation-profile outgoing pstn-out
destination-pattern 0T
incoming called-number .
direct-inward-dial
port 0/0/0:15
forward-digits all
!
dial-peer voice 100 pots
description Emergency outbound
translation-profile outgoing pstn-out
destination-pattern 1..
port 0/0/0:15
forward-digits all
!
dial-peer voice 900 pots
description Emergency and Services outbound
translation-profile outgoing pstn-out
destination-pattern 9..
port 0/0/0:15
forward-digits all
!
dial-peer voice 11 pots
description LCR to Mobile
preference 1
service mgcpapp
destination-pattern 07[1378]T
port 0/1/0
forward-digits all
!
dial-peer voice 12 pots
description LCR to Mobile
preference 2
service mgcpapp
destination-pattern 07[1378]T
port 0/1/1
forward-digits all
!
dial-peer voice 13 pots
description LCR to Mobile
preference 3
service mgcpapp
destination-pattern 07[1378]T
port 0/1/2
forward-digits all
!
dial-peer voice 14 pots
description LCR to Mobile
preference 4
service mgcpapp
destination-pattern 07[1378]T
port 0/2/0
forward-digits all
!
dial-peer voice 15 pots
description LCR to Mobile
preference 5
service mgcpapp
destination-pattern 07[1378]T
port 0/2/1
forward-digits all
!
dial-peer voice 16 pots
description LCR to Mobile
preference 6
service mgcpapp
destination-pattern 07[1378]T
port 0/2/2
forward-digits all
!
dial-peer voice 21 pots
description LCR to Mobile
preference 1
service mgcpapp
destination-pattern 086T
port 0/1/0
forward-digits all
!
dial-peer voice 22 pots
description LCR to Mobile
preference 2
service mgcpapp
destination-pattern 086T
port 0/1/1
forward-digits all
!
dial-peer voice 23 pots
description LCR to Mobile
preference 3
service mgcpapp
destination-pattern 086T
port 0/1/2
forward-digits all
!
dial-peer voice 24 pots
description LCR to Mobile
preference 4
service mgcpapp
destination-pattern 086T
port 0/2/0
forward-digits all
!
dial-peer voice 25 pots
description LCR to Mobile
preference 5
service mgcpapp
destination-pattern 086T
port 0/2/1
forward-digits all
!
dial-peer voice 26 pots
description LCR to Mobile
preference 6
service mgcpapp
destination-pattern 086T
port 0/2/2
forward-digits all
!
dial-peer voice 99901990 pots
service mgcpapp
port 0/1/0
!
dial-peer voice 99901991 pots
service mgcpapp
port 0/1/1
!
dial-peer voice 99901992 pots
service mgcpapp
port 0/1/2
!
dial-peer voice 99902990 pots
service mgcpapp
port 0/2/0
!
dial-peer voice 99902991 pots
service mgcpapp
port 0/2/1
!
dial-peer voice 99902992 pots
service mgcpapp
port 0/2/2
!
dial-peer voice 99901099 pots
service mgcpapp
port 0/1/0
!
dial-peer voice 99901199 pots
service mgcpapp
port 0/1/1
!
dial-peer voice 99901299 pots
service mgcpapp
port 0/1/2
!
dial-peer voice 99902099 pots
service mgcpapp
port 0/2/0
!
dial-peer voice 99902199 pots
service mgcpapp
port 0/2/1
!
dial-peer voice 99902299 pots
service mgcpapp
port 0/2/2
!
dial-peer voice 99901993 pots
service mgcpapp
port 0/1/3
!
dial-peer voice 66 pots
description LCR to Mobile
preference 4
service mgcpapp
destination-pattern 07[1378]T
port 0/1/3
forward-digits all
!
dial-peer voice 99901399 pots
service mgcpapp
port 0/1/3
!
!
sip-ua
registrar ipv4:10.248.34.102 expires 600
!
!
!
gatekeeper
shutdown
!
!
call-manager-fallback
max-conferences 8 gain -6
transfer-system full-consult
timeouts interdigit 6
ip source-address 10.248.34.102 port 2000
max-ephones 100
max-dn 100 dual-line
system message primary Link Down Limited Functionality
transfer-pattern .T
transfer-pattern 8198....
keepalive 10
translation-profile incoming phones-in
moh enable-g711 "SampleAudioSource.ulaw.wav"
multicast moh 239.1.1.3 port 16384 route 10.149.250.2 10.248.34.102
date-format dd-mm-yy
!
!
banner exec ^C

        If you are not authorised to access this device then

                          Please log off now.

*** ALL Commands from this device are Authorised Authenticated & Accounted ***
^C
banner login ^C
British Telecommunications plc

WARNING: You have accessed a network device operated by BT. You are required
to have a personal authorisation from the system administrator before you use
this computer and you are strictly limited to the use set out in that written authorisation.
Unauthorised access to or misuse of this system is prohibited
and may constitute an offence under the Computer Misuse Act 1990.

If you disclose any information obtained through this system without authority
BT will take appropriate action against you. This may include legal
proceedings, prosecution and disciplinary action up to and including
dismissal.
^C
!
line con 0
exec-timeout 15 0
password 7 00060715114B1B091D35
logging synchronous
line aux 0
no exec
transport output none
line 2
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
exec-timeout 15 0
password 7 0509121C345C5E060B11
logging synchronous
transport preferred ssh
transport input telnet ssh
transport output telnet ssh
line vty 5 15
exec-timeout 15 0
password 7 0509121C345C5E060B11
logging synchronous
transport preferred ssh
transport input telnet ssh
transport output telnet ssh
!
scheduler allocate 20000 1000
ntp source Loopback10
ntp update-calendar
ntp server 199.80.49.161
ntp server 199.80.49.170 prefer
!
end

Regards,

Edwin

Marcelo Morais · ‎06-06-2015

Hi,

you use a MGCP protocol to both of your FXO configuration, in other words, your should configure your FXO in your Call Control - CUCM (IP Addr 10.144.56.10).

Did you configure both FXOs in your CUCM?

Hope this helps.

abc4308449 · ‎06-07-2015

All FXO ports a registered with the call manager, problem is when I plugin my analogue phone to the LCR i get a dial tone but when I plugin my LCR to the FXO port I hear nothing, dead!

" you use a MGCP protocol to both of your FXO configuration, in other words, your should configure your FXO in your Call Control - CUCM (IP Addr 10.144.56.10)"

Meaning? can you please provide me with the step-by-step process to follow please.

Marcelo Morais · ‎06-07-2015

Hi,

when you configured the FXO in CUCM, you did that in CUCM Administration > Device > Gateway > <select the GW model> > choose MGCP > select the Module/Sub-Unit.

What Port-Type did you select? Ground Start or Loop Start?

Regards.

abc4308449 · ‎06-08-2015

loop Start is the port i choose i ahve also tried to change it to ground start still calls are not going out through the LCR