04-13-2010 02:36 PM - edited 03-15-2019 10:15 PM
Best regards.
To download L-CM-DL, I need the "License MAC"
To find address I did the following step:
1. Log in to the Cisco UCM command line interface (CLI) and enter show status.
But in this devices the "show status" comando not exist.
The MCS have 3 Mac address, 2 Giga ethernet and 1 Service-Engine interface,
Which I can use to download the license or which command can I use to see the License MAC.
Thank for help me.
Solved! Go to Solution.
05-27-2010 12:15 PM
On your particular version (6.1.2), you use command "show network eth0 detail" to get the MAC address:
admin:show network eth0 detail
Ethernet 0
DHCP : disabled Status : up
IP Address : 10.88.7.221 IP Mask : 255.255.255.000
Link Detected: yes Mode : Auto disabled, Full, 1000 Mbits/s
Duplicate IP : no
Queue Length : 1000 MTU : 1500
MAC Address : 00:0c:29:8a:7e:49
RX stats:
bytes : 3219412021 packets : 15179215 errors : 43
dropped : 0 overrun : 0 mcast : 0
TX stats:
bytes : 1267274831 packets : 9269296 errors : 0
dropped : 0 carrier : 0 colsns : 0
Michael
04-13-2010 02:39 PM
Hi
It sounds like you are looking at a Cisco ISR or other router - not an MCS server.
Can you do a 'show version' on this device?
Aaron
04-13-2010 02:50 PM
Yes, the output of show version command is:
Cisco IOS Software, 3800 Software (C3825-ADVIPSERVICESK9-M), Version 12.4(9)T7, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Thu 10-Jan-08 18:20 by prod_rel_team
ROM: System Bootstrap, Version 12.4(13r)T10, RELEASE SOFTWARE (fc1)
RO-GPA-01 uptime is 7 weeks, 5 days, 19 hours, 12 minutes
System returned to ROM by power-on
System restarted at 20:06:54 UTC Fri Jan 15 2010
System image file is "flash:c3825-advipservicesk9-mz.124-9.T7.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Cisco 3825 (revision 1.2) with 484352K/39936K bytes of memory.
Processor board ID FTX1236A0YP
2 Gigabit Ethernet interfaces
1 terminal line
1 Virtual Private Network (VPN) Module
28 Voice FXO interfaces
4 Voice FXS interfaces
1 cisco service engine(s)
DRAM configuration is 64 bits wide with parity enabled.
479K bytes of NVRAM.
125440K bytes of ATA System CompactFlash (Read/Write)
Configuration register is 0x2102
04-13-2010 03:05 PM
Hi
OK - so when you are registering CallManager DLUs, you register these to your publisher MAC address. The publisher (and all other MCS servers) is a HP or IBM based server.
What you have is a router, which can be used as a telephony system if you configure CallManager Express on it.
You can't install DLUs on a router; and you don't need them.
Do you have an actual MCS server and CallManager software?
Aaron
05-27-2010 11:31 AM
Hi Aaron.
I have a MCS server 7828-I3
But the output of show status command is:
admin:show status
Host Name : CM7828
Date : Thu May 27, 2010 13:28:52
Time Zone : America/Guayaquil
Locale : en_US.UTF-8
Product Ver : 6.1.2.1000-13
Platform Ver : 2.0.0.1-1
Uptime:
13:28:53 up 9 days, 18:04, 1 user, load average: 0.22, 0.40, 0.47
CPU Idle: 89.90% System: 01.01% User: 02.02%
IOWAIT: 05.56% IRQ: 00.00% Soft: 01.52% Intr/sec: 440.40
Memory Total: 6156852K
Free: 28744K
Used: 6128108K
Cached: 3084140K
Shared: 0K
Buffers: 127584K
Total Free Used
Disk/active 43264144K 36138388K 6686220K (16%)
Disk/inactive 43264176K 41033656K 32828K (1%)
Disk/logging 150538756K 122603092K 20288728K (15%)
admin:
I have not publisher MAC Addrees.
Which command I can use to get the MAC
Thanks.
Jose
05-27-2010 12:15 PM
On your particular version (6.1.2), you use command "show network eth0 detail" to get the MAC address:
admin:show network eth0 detail
Ethernet 0
DHCP : disabled Status : up
IP Address : 10.88.7.221 IP Mask : 255.255.255.000
Link Detected: yes Mode : Auto disabled, Full, 1000 Mbits/s
Duplicate IP : no
Queue Length : 1000 MTU : 1500
MAC Address : 00:0c:29:8a:7e:49
RX stats:
bytes : 3219412021 packets : 15179215 errors : 43
dropped : 0 overrun : 0 mcast : 0
TX stats:
bytes : 1267274831 packets : 9269296 errors : 0
dropped : 0 carrier : 0 colsns : 0
Michael
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide