02-18-2014 09:13 AM - edited 03-16-2019 09:48 PM
Hello,
help me pls,
I cant perform call from IP Phone on CME to NEC phone after migration on new IOS 15.2.4(M4)
CME - <sip> - CUBE - <pri> - NEC
the same config on 12.4(24)T3 working without any problems.
007985: Feb 18 19:06:32 MSK: ISDN Se0/0/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Calling num 85742
007986: Feb 18 19:06:32 MSK: ISDN Se0/0/0:15 Q931: Sending SETUP callref = 0x03DF callID = 0x8360 switch = primary-net5 interface = Network
007987: Feb 18 19:06:32 MSK: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref = 0x03DF
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Display i = 'TEST'
Calling Party Number i = 0x0180, '85742'
Plan:ISDN, Type:Unknown
Called Party Number i = 0x81, '1567'
Plan:ISDN, Type:Unknown
007988: Feb 18 19:06:32 MSK: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0x03DF
Cause i = 0x8290 - Normal call clearing
007989: Feb 18 19:06:32 MSK: ISDN Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x83DF
Channel ID i = 0xA98381
Exclusive, Channel 1
007990: Feb 18 19:06:32 MSK: ISDN Se0/0/0:15 Q931: RX <- ALERTING pd = 8 callref = 0x83DF
Channel ID i = 0xA98381
Exclusive, Channel 1
Progress Ind i = 0x8182 - Destination address is non-ISDN
007991: Feb 18 19:06:32 MSK: ISDN Se0/0/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x83DF
007992: Feb 18 19:06:32 MSK: ISDN Se0/0/0:15 **ERROR**: Ux_BadMsg: Invalid Message for call state 11, call id 0x8360, call ref 0x3DF, event 0x2
007993: Feb 18 19:06:32 MSK: ISDN Se0/0/0:15 **ERROR**: Ux_BadMsg: Invalid Message for call state 11, call id 0x8360, call ref 0x3DF, event 0x1
007994: Feb 18 19:06:32 MSK: ISDN Se0/0/0:15 Q931: TX -> STATUS pd = 8 callref = 0x03DF
Cause i = 0x80E202 - Message not compatible with call state or not implemented
Call State i = 0x0C
007995: Feb 18 19:06:32 MSK: ISDN Se0/0/0:15 Q931: TX -> STATUS pd = 8 callref = 0x03DF
Cause i = 0x80E201 - Message not compatible with call state or not implemented
Call State i = 0x0C
007996: Feb 18 19:06:32 MSK: ISDN Se0/0/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x03DF
02-18-2014 09:38 AM
If the same config works with 12.X but not with 15.X, then it could be issue of toll fraud application. Please check this url http://www.cisco.com/c/en/us/support/docs/voice/call-routing-dial-plans/112083-tollfraud-ios.html
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide