01-19-2009 04:31 AM - edited 03-15-2019 03:36 PM
Earlier I could call from translation pattern with mask in configured Translation Pattern. Now I cann't . Is it some bug??
CSS, Partitions and Translation pattern configured right
01-19-2009 04:40 AM
When I call #933555555 I want to go out to PSTN with number 782090
but I go out with line external mask number
01-19-2009 04:50 AM
Please, use dialed number analyser tool and post the output?
01-19-2009 05:28 AM
Results Summary
Calling Party Information
Calling Party = 782099 <--RIGHT NUMBER
Partition =
Device CSS =
Line CSS = Kiev_Employers_CSS
AAR Group Name =
AAR CSS =
Dialed Digits = #933782200
Match Result = RouteThisPattern
Matched Pattern Information
Pattern = [27]XXXXX
Partition = Lt_City_PT
Time Schedule =
Called Party Number = 782200
Time Zone = Greenwich Standard Time
End Device = Lt_RL
Call Classification = OnNet
InterDigit Timeout = NO
Device Override = Disabled
Outside Dial Tone = NO
Call Flow
TranslationPattern :Pattern= #933.!
Positional Match List = 782200
Calling Party Number = 782099
PreTransform Calling Party Number = 1129
PreTransform Called Party Number = #933782200
Calling Party Transformations
External Phone Number Mask = NO
Calling Party Mask = 78209X
Prefix =
CallingLineId Presentation = Default
CallingName Presentation = Default
Calling Party Number = 782099
ConnectedParty Transformations
ConnectedLineId Presentation = Default
ConnectedName Presentation = Default
Called Party Transformations
Called Party Mask =
Discard Digits Instruction = PreDot
Prefix =
Called Number = 782200
Route Pattern :Pattern= [27]XXXXX
Positional Match List = 782200
DialPlan =
Route Filter
Filter Name =
Filter Clause =
Require Forced Authorization Code = No
Authorization Level = 0
Require Client Matter Code = No
Call Classification =
PreTransform Calling Party Number = 782099
PreTransform Called Party Number = 782200
Calling Party Transformations
External Phone Number Mask = YES
Calling Party Mask =
Prefix =
CallingLineId Presentation = Default
CallingName Presentation = Default
Calling Party Number = 782099
ConnectedParty Transformations
ConnectedLineId Presentation = Default
ConnectedName Presentation = Default
Called Party Transformations
Called Party Mask =
Discard Digits Instruction = None
Prefix =
Called Number = 782200
Route List :Route List Name= Lt_RL
RouteGroup :RouteGroup Name= Lt_RG
PreTransform Calling Party Number = 782099
PreTransform Called Party Number = 782200
Calling Party Transformations
External Phone Number Mask = Default
Calling Party Mask =
Prefix =
Calling Party Number = 782099
Called Party Transformations
Called Party Mask =
Discard Digits Instructions =
Prefix =
Called Number = 782200
Device :Type= MGCPE1PRIPort
End Device Name = S0/SU0/DS1-0@C3825.cisco.net
PortNumber = 0
Device Status = Registered
AAR Group Name =
AAR Calling Search Space =
AAR Prefix Digits =
Call Classification =
Calling Party Selection =
CallingLinePresentation =
ConnectedLinePresentation =
Number Of Strip Digits =
CallerID DN =
Alternate Matches
Note: Information Not Available
01-19-2009 05:29 AM
debug isdn q931
Jan 19 13:28:29.136: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref = 0x00A0
Sending Complete
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9839E
Exclusive, Channel 30
Calling Party Number i = 0x0081, '5930029' <-- NO NEEDED NUMBER
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '780002'
Plan:Unknown, Type:Unknown
Jan 19 13:28:29.152: ISDN Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x80A0
Channel ID i = 0xA9839E
Exclusive, Channel 30
Jan 19 13:28:29.300: ISDN Se0/0/0:15 Q931: RX <- ALERTING pd = 8 callref = 0x80A0
Jan 19 13:28:30.044: ISDN Se0/0/0:15 Q931: RX <- CONNECT pd = 8 callref = 0x809F
Channel ID i = 0xA9839F
Exclusive, Channel 31
Date/Time i = 0x0901130F1C00
01-19-2009 08:54 AM
in the past when i've seen this the issue wasn't even CCM, it was the GW.
the only way to confirm this is getting a CUCM detailed trace, looking at the call info line for the call and reviewing the setup message sent by CUCM, if all the info matches but still the GW sends something else the options are try a no mgcp/mgcp and/or reload the GW
HTH
java
if this helps, please rate
01-19-2009 09:33 AM
I was very confused when saw that this solution doesn't work.
It worked with CCM 4.3 - but after upgrade I only now checked that I have some problems.
I have done no mgcp / mgcp ofcourse, but it was helped.
Let's try to to upgrade CUCM..
01-20-2009 12:08 AM
Hi
Have you tried restarting CCM service?
Txs
Pedro
01-20-2009 10:14 AM
Not yet..I think this could help me
Thanks
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide