11-17-2021 04:47 PM
Hello,
R1's gig1 is connected with r2's gig1.
R1-------------R2
I have created subinterfaces on R1 and R2. and assigned IPv6 addresses to newly created subinterfaces.
R1
ipv6 unicast-routing
Router#show run int g1.2
interface GigabitEthernet1.2
encapsulation dot1Q 2
ipv6 address 2001::1/64
ipv6 enable
end
R2
ipv6 unicast-routing
interface GigabitEthernet1.2
encapsulation dot1Q 2
ipv6 address 2001::2/64
ipv6 enable
end
When I try to ping from R1's gig1.2 to R2's gig1.2 I get the following error.
R1#ping 2001::2 source gigabitEthernet 1.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2001::2, timeout is 2 seconds:
Packet sent with a source address of 2001::1
.H..H
Success rate is 0 percent (0/5)
Why ping is not working?
Thanks!
Solved! Go to Solution.
11-17-2021 05:47 PM
Hi @sachin30720041 ,
I suppose this is on the CSR1000v, right?
If so, this is due to the different way this platform deals with dot1q traffic.
Try the following instead:
R1:
no interface GigabitEthernet1.2
interface GigabitEthernet1
no ip address
service instance 2 ethernet
encapsulation dot1q 2
!
bridge-domain 2
member GigabitEthernet1 service-instance 2
!
interface BDI2
encapsulation dot1Q 2
ipv6 address 2001::1/64
no shutdown
R2:
no interface GigabitEthernet1.2
interface GigabitEthernet1
no ip address
service instance 2 ethernet
encapsulation dot1q 2
!
bridge-domain 2
member GigabitEthernet1 service-instance 2
!
interface BDI2
encapsulation dot1Q 2
ipv6 address 2001::2/64
no shutdown
That should solve your issue.
Regards,
11-17-2021 05:47 PM
Hi @sachin30720041 ,
I suppose this is on the CSR1000v, right?
If so, this is due to the different way this platform deals with dot1q traffic.
Try the following instead:
R1:
no interface GigabitEthernet1.2
interface GigabitEthernet1
no ip address
service instance 2 ethernet
encapsulation dot1q 2
!
bridge-domain 2
member GigabitEthernet1 service-instance 2
!
interface BDI2
encapsulation dot1Q 2
ipv6 address 2001::1/64
no shutdown
R2:
no interface GigabitEthernet1.2
interface GigabitEthernet1
no ip address
service instance 2 ethernet
encapsulation dot1q 2
!
bridge-domain 2
member GigabitEthernet1 service-instance 2
!
interface BDI2
encapsulation dot1Q 2
ipv6 address 2001::2/64
no shutdown
That should solve your issue.
Regards,
11-23-2021 03:19 PM
Hi @sachin30720041 ,
Did you get a chance to test the proposed solution?
Regards,
11-27-2021 12:33 PM
Hi Harold,
With the above mentioned configuration ping is working.
Thanks,
Sachin
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide