ATM/E1 connection between 7200 E1-IMA and 2651 VWIC-1MFT-E1
I have a 7200 with an E1-IMA card.
I have a 2651 with a VWIC-1MFT-E1.
I have them connected via an E1 cross-over (the cable has been tested between 2x7200 E1-IMA cards)
I can't get them to talk to each other.
Both ends show the PVC as: Status: up and have green LED link lights
But one end shows the IP interface as up, the other end down
Can anyone help?
7200 with E1-IMA
2651 with VWIC-1MFt-E1
hostname 7200-E1-IMA ip cef ! interface ATM1/0 no ip address clock source internal
no ima-group no atm ilmi-keepalive ! interface ATM1/0.1 point-to-point ip address 10.10.10.1 255.255.255.248 pvc 0/44 ubr 1920 encapsulation aal5snap
hostname 2651-VWIC-1MFT-E1 ip cef
controller E1 0/0 mode atm
clock source internal
interface ATM0/0 no ip address no atm ilmi-keepalive ! interface ATM0/0.1 point-to-point ip address 10.10.10.2 255.255.255.248 pvc 0/44 ubr 1920 encapsulation aal5snap
7200-E1-IMA#show atm pvc VCD / Peak Avg/Min Burst Interface Name VPI VCI Type Encaps SC Kbps Kbps Cells Sts 1/0.1 1 0 44 PVC SNAP UBR 1920 UP
2651-VWIC-1MFT-E1#show atm pvc VCD / Peak Avg/Min Burst Interface Name VPI VCI Type Encaps SC Kbps Kbps Cells Sts 0/0.1 1 0 44 PVC SNAP UBR 1920 UP
7200-E1-IMA#sh ip int br Interface IP-Address OK? Method Status Protocol ATM1/0 unassigned YES NVRAM up up ATM1/0.1 10.10.10.1 YES manual up up
2651-VWIC-1MFT-E1#sh ip int br Interface IP-Address OK? Method Status Protocol FastEthernet0/0 10.10.100.2 YES NVRAM up up FastEthernet0/1 unassigned YES NVRAM administratively down down ATM0/0 unassigned YES manual down down ATM0/0.1 10.10.10.2 YES manual down down
7200-E1-IMA#sh ver Cisco Internetwork Operating System Software IOS (tm) 7200 Software (C7200-IS-M), Version 12.3(1a), RELEASE SOFTWARE (fc1)
System image file is "slot0:c7200-is-mz.123-1a.bin"
2651-VWIC-1MFT-E1#sh ver Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-JS-M), Version 12.2(2)XT, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
System image file is "flash:c2600-js-mz.122-2.XT.bin"
In EVPN A/A + IRB both PE in same EVI have BVI playing a default GW role. Its not supported to have BVI to be shutdown on one of PEs, In this case if if traffic hit this PE with DMAc equal to BVI Custom MAC, then it will drop this traffic du...
Crosswork Cloud - Crosswork Traffic Analysis - FAQ
Crosswork Cloud - Crosswork Traffic Analysis is a Cloud-hosted Software as a Service platform that provides Netflow based Traffic Analytics. The Crosswork Traffic Analysis platform Traffic Analysis, Peeri...
Cisco Champion Radio · S8|E9 Innovations to Achieve a Trustworthy Infrastructure
How do you know for certain that a router in your network has not been altered with since you deployed it? Wouldn’t it be great if you can cryptographically challenge your r...
IOS upgrade on asr9xx mandates rommon upgrades sometimes while they can be optional at other times. You may land up in unwanted situation if proper procedure is not followed during upgrades.
This article will include complete details about rommon ...
In some situation NCS560 RP become unresponsive after reload or powercycle.
In many NCS560 deployments are in remote location, deployment might be large and human intervention should be kept at minimum
Engineering team have been working on a str...