07-17-2015 03:57 AM
I've set up the following lab. The "customers", most of the purple devices have no problem with connectivity at layer 2 or 3 except R16 and R19.
The problem between S20 and R6/R12, as if I get R12/R6 to switch to their backup xconnect neighbours (Device 3) it works fine, R16 and R19 find the other customers.
Routers 12 and 6 are not capable of manual VFI's thus have been xconnected to S20 with a backup to Device 3.
S20 is a 6500 running ADVENTERPRISEK9 12.2(33)SXI6
Devices 1-3 are ASR 920's
R12 and R6 both 2811 running adventerprisek9-mz.124-15.T9
Any ideas greatly appreciated
R6#show xcon all
Legend: XC ST=Xconnect State, S1=Segment1 State, S2=Segment2 State
UP=Up, DN=Down, AD=Admin Down, IA=Inactive, NH=No Hardware
XC ST Segment 1 S1 Segment 2 S2
------+---------------------------------+--+---------------------------------+--
UP pri ac Fa0/1(Ethernet) UP mpls 1.0.0.21:100 UP
IA sec ac Fa0/1(Ethernet) UP mpls 1.0.0.33:100 DN
S20#show vfi
Legend: RT=Route-target, S=Split-horizon, Y=Yes, N=No
VFI name: PORTAL, state: up, type: multipoint
VPN ID: 100
Local attachment circuits:
Vlan5
Neighbors connected via pseudowires:
Peer Address VC ID S
1.0.0.31 100 Y
1.0.0.6 100 N
1.0.0.12 100 N
1.0.0.11 100 N
1.0.0.33 100 Y
1.0.0.32 100 Y
S20#show mpls l2 vc
Local intf Local circuit Dest address VC ID Status
------------- -------------------------- --------------- ---------- ----------
VFI PORTAL VFI 1.0.0.6 100 UP
VFI PORTAL VFI 1.0.0.11 100 UP
VFI PORTAL VFI 1.0.0.12 100 UP
VFI PORTAL VFI 1.0.0.31 100 UP
VFI PORTAL VFI 1.0.0.32 100 UP
VFI PORTAL VFI 1.0.0.33 100 UP
07-19-2015 03:27 AM
07-23-2015 03:28 AM
I thought, I'd fixed it......
I did find
But I tried both a trunk and access port across to S2 from S20 with no luck. As soon as that VFI on S20 comes up devices R15, 16, 19 all drop their connections.
I'm not sure if its a consequence or cause but none of the MPLS L2 VC's leaving S20 have any outgoing packets.
Local interface: VFI PORTAL VFI up
Interworking type is Ethernet
Destination address: 1.0.0.31, VC ID: 100, VC status: up
Output interface: none, imposed label stack {}
Preferred path: Tunnel31, active
Default path: disabled
No adjacency
Load Balance: none
Flow Label: Disabled
Create time: 00:08:16, last status change time: 00:00:07
Signaling protocol: LDP, peer 1.0.0.31:0 up
Targeted Hello: 1.0.0.20(LDP Id) -> 1.0.0.31, LDP is UP
Status TLV support (local/remote) : enabled/not supported
LDP route watch : enabled
Label/status state machine : established, LruRru
Last local dataplane status rcvd: No fault
Last local SSS circuit status rcvd: No fault
Last local SSS circuit status sent: No fault
Last local LDP TLV status sent: No fault
Last remote LDP TLV status rcvd: Not sent
Last remote LDP ADJ status rcvd: No fault
MPLS VC labels: local 35, remote 38
Group ID: local 0, remote 0
MTU: local 1500, remote 1500
Remote interface description:
MAC Withdraw: sent:1, received:0
Sequencing: receive disabled, send disabled
Control Word: On (configured: autosense)
VC statistics:
transit packet totals: receive 1088, send 0
transit byte totals: receive 120240, send 0
transit packet drops: receive 0, send 0
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide