01-19-2011 01:35 AM - edited 03-10-2019 05:43 PM
Hi All,
I hope some one can help out with this problem.
I have an ACS 5.1 with the following S/W load
Cisco Application Deployment Engine OS Release: 1.2
ADE-OS Build Version: 1.2.0.146
ADE-OS System Architecture: i386
Cisco ACS VERSION INFORMATION
-----------------------------
Version : 5.1.0.44
Internal Build ID : B.2347
I have downloaded 5-1-0-44-3.tar.gpg, 5-1-0-44-4.tar.gpg and 5-1-0-44-5.tar.gpg to a local repository on the ACS but when ever I try and run the patch upgrade process acs patch install 5-1-0-44-5.tar.gpg repository repository_name I get the following error output....
chmod: cannot access `*.sh': No such file or directory
Invalid patch '5-1-0-44-5.tar.gpg' - missing install.sh
% Error: Failure to open / validate the patch
I have moved the 5-1-0-44-5.tar.gpg to a linux box and have tried to dencrypt the file using gpg -d 5-1-0-44-5.tar.gpg but it then prompts for apass phrase, I tried a few guesses but I could not decrypt it.
So what part of the upgrade process am I missing, or do I need to install some sort of pass phrase so that the ACS can properly decrypt the patch files.
I have tried this with patch 3, 4 and 5. Do I need to start off at pathch 1?
Thanks
Cefyn Arch
Solved! Go to Solution.
01-19-2011 02:30 AM
Helloz,
Form where did you download the patch. I would suggest you to download from cisco.comif you didn't download before.
http://tools.cisco.com/squish/1D47B
No, You can directly apply the patch 5.
The command you are running to apply the patch is correct.
I would like you to check the few things
1. Are you using TFTP? IF yes, then switch to FTP and then try.
2. Before you apply the patch, make sure you can see the file under the repository.
Show repository
if you can see patch 5 under the repository then you are good to go.
HTH
Jatin
~Do rate helpful posts
01-19-2011 02:30 AM
Helloz,
Form where did you download the patch. I would suggest you to download from cisco.comif you didn't download before.
http://tools.cisco.com/squish/1D47B
No, You can directly apply the patch 5.
The command you are running to apply the patch is correct.
I would like you to check the few things
1. Are you using TFTP? IF yes, then switch to FTP and then try.
2. Before you apply the patch, make sure you can see the file under the repository.
Show repository
if you can see patch 5 under the repository then you are good to go.
HTH
Jatin
~Do rate helpful posts
01-19-2011 09:52 AM
Hi Jatin,
Thanks for the advice to change to FTP. Once I had moved the file using FTP there was no corruption and the update would apply.
Is TFTP on the ACS operating system broken ?
Cefyn
01-19-2011 11:24 AM
Yes, there is an issues with TFTP and we also filed a defect on that.
Regards,
Jatin
Do rate helpfuls posts~
06-29-2014 06:48 PM
I also had the same issue attempting to install the latest patch for version 5.2.
Using TFTP caused the ACS to say it cannot find install.sh but when using FTP, the upgrade worked fine.
Thanks
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide