Network Access Control

Here is my problem. Why can I not log into the ACS server via ssh but I can log in to the gui interface on http?I get the username and password prompt without a problem but it will not accept my username and password.Any thoughts?Thanks

All,We are currently running ACS 3.3 on a Windows 2003 member server of our domain.  It has become necessary for the server administrators to upgrade our domain controllers from Windows 2003 to Windows 2008.  Since we have no interest of running ACS ...

Hi all,I have created a shell profile with a default Privilege level of 15, I am able to successfully call this via an Access Service Rule. The issue I have however is that depite having the # symbol after I log in, the switch will only allow me to p...

Hi all,We have and Cisco ACS v4.2 on a Cisco Appliance, and we need to integrate it with Active Directory. Can you help me??Thanks for your helpRegards!!!Rafael Turriago

Hi group,I'm configuring downloadable ACL on ACS 5.1 for authorized vpn users. Whenever users log in to vpn through ASA then they will get individual ACL.I checked AAA Protocol > RADIUS Authentication Report and found something like #ACSACL#-IP-testD...

i want the configuration steps that integrate ACS with LDAP , and i want to match the attributes of specific domain user "like sAMAccount" , and apply access control policy on this specific LDAP username .

Hello,Can someone help me, I have this error when I try to login on Redhat server :TacacsLoginFlow,22/11/2010,18:41:58:347,ERROR,3057433504,cntx=0003764282,sesn=EMEA-PAR-ACS01/78155693/561084,user=user-name,Failed to dispatch the T+ Authen Login pack...

Hi ...Just setup Cisco 7606 Router by console with IOS version s72033-advipservicesk9_wan-mz.122-33.SRA3.bin.username xxxx password 7 xxxxxxxxaaa new-modelaaa authentication login default group tacacs+ localaaa authentication enable default group tac...

Hi,I am using ACS V 4.1 .Under reports and activity when i try to check for TACACS+ administration report the report is getting generated but there is no data avaliable in the report.In the router side the AAA configuration is proper,Please help in t...

Basically for integration of the role based CLI to a particular user in 1800 aeries router is as follows.....(Conf )# username JAMES view SHOWMODE secret CISCObut when this command is run in 2800 series router this doesn't work so how can this be don...

Recently I'm using ACS 5.1 to support external RADIUS Servers, and read the manauls to process with the following workflow.Install Linux RADIUS Service (this part was tested)Install FreeRADIUS ServiceAdd new linux user account Cisco ACS 5.1Add Extern...

This past weekend we did an upgrade from 5.1 to 5.2 (backup, re-image, restore backup).  /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-styl...

Hello,We are are running ACS 5.0 and trying to backup ACS log files but the backup fails and we have the following error :TNAACSCS01A5/admin# show repository repacs*** glibc detected *** free(): invalid pointer: 0xbffdddf8 ***¸Þý¿hˈﷀ¸ï·hËÊ% Intern...

It is possible to take a backup from CSACS running on a Solution Engine (FTP'd off-box by the backup process) and restore it to a CSACS on Windows (assuming the ACS software, build, and patch level is same?

Hi,I have configured Nexus 7000 for Radius authentication. Login is being shown successfull on RSA server However login on Nexus is not successful giving the below error.C15F0DCCODS3# 2010 Nov 19 13:44:01 C15F0DCCODS3 %AUTHPRIV-3-SYSTEM_MSG: pam_aaa:...