About Valkyrie3

Valkyrie3 · 01-07-2026

I've not dealt with management ports very often (most switches I manage use SVi's) so I don't know if I'm doing something stupid or misunderstanding the config, I'd appreciate some guidance since I'm not making much progress myself.I have upgraded a ...

Valkyrie3 · 12-24-2025

I think I'm encountering this bug here:https://bst.cloudapps.cisco.com/bugsearch/bug/CSCwo48630There's a task stuck called Policy Changes Report Request - Policy preview diff generation is in progressI was going to start maintenance work on a FTDv HA...

Valkyrie3 · 05-01-2025

I have an FMC 2700 on version 7.4.2.1 which is managing an FTDv running 7.2.9 and having a problem getting a site to site VPN working, it's the 5th one I've set up and the first one to this particular company (the other four have all worked fine firs...

Valkyrie3 · 02-06-2025

I have a UCS 5108 chassis with eight B200 M5's, I upgraded the chassis manager from 4.3.4a to 4.3.5a at Christmas time but when upgrading a blade from 4.2.1f to 4.3.5a this week it failed at the following step:Associate Check Power Availability - Che...

Valkyrie3 · 09-11-2024

I'm using a pair of C8000v routers which have been working well until recently the site has been encountering internet performance issues, I found the following error when the problem is starting:%IOSXE-4-PLATFORM: R0/0: cpp_cp: QFP:0.0 Thread:000 TS...

Valkyrie3 · 01-07-2026

Really appreciate all the replies and it's been really helpful with these additional commands so I can see the L2 was all fine, it turns out there was a stupid mistake.There was an ACL copied across from the previous switch that was meant to limit SS...

Valkyrie3 · 01-07-2026

Thanks also for the quick response. I've run the commands but had to change how I'm showing the IP addresses because of some of the responses I'm seeing to make sense, these are the IP addresses/ranges:192.168.53.0/24 - the existing management subne...

Valkyrie3 · 01-07-2026

The switch is tucked in tight with other equipment but it looks like the management LED light is on, the light on the management switch is definitely lit. The output command is as follows:show int gigabitEthernet 0/0GigabitEthernet0/0 is up, line pr...

Valkyrie3 · 12-29-2025

Thanks for the replies, I decided to just go ahead and get a TAC call raised and they advised I could still deploy (I'm not sure how I was getting the warning stopping the deployment) so I've managed to get the maintenance work I wanted done. I can ...

Valkyrie3 · 05-07-2025

The vendor has replied saying they changed the local and remote CIDR's on their side which brought the phase one tunnel up but there was an authentication error. I changed to a new shared secret and provided it to the vendor so the VPN is now finall...

Member Since	‎09-23-2022 04:54 AM
Date Last Visited	‎01-09-2026 11:28 PM
Posts	38
Total Helpful Votes Received	8

User Statistics

User Activity

Unable to get management port on Cisco 9300X to connect

Deployment is failing due to the policy changes report request in prog

No proposal chosen on FMC managed FTDv - any helpful debug commands?

Check power availability failure after upgrading blade to 4.3.5a

Increase max NAT translation limit on c8000v router

Re: Unable to get management port on Cisco 9300X to connect

Re: Unable to get management port on Cisco 9300X to connect

Re: Unable to get management port on Cisco 9300X to connect

Re: Deployment is failing due to the policy changes report request in

Re: No proposal chosen on FMC managed FTDv - any helpful debug command