Network Access Control

Is there a way to have a single login when using Win2k or XP clients connecting to a 3550 switch set up with 802.1x port authentication to a ACS server version 3.1? I have been beating myself up trying to get to a single login that when the person p...

I had both ACS 3.0 and VRM installed in the same NT 4.0 Machine.ACS ports had been changed in registry asAuthentication: 1812Accounting:1813VRM ports uses standard IETFAuthentication: 1645Accounting:1646All user token authentication works fine and AC...

I am using AS5300 and my NAS is dropping stop packets.Radius server is located at remote location connected through radio link.Please help for solving this problem.aaa new-modelaaa group server radius rkt server 1.2.3.4 auth-port 1645 acct-port 1646!...

I'm going to be installing the above metioned software on a Sun 280R with Solaris 9 and multiple NIC's on it.Can the TACACS+ and Radius services be bound to listen on one NIC while the management is listening on a different nic?

Hello.I would like to know if is possible, with cisco secure ACS for windows,to load radius dictionary files provided by other vendors?If yes, how is it possible to do it?Thank you

HiDo I have to have CBAC on a Cisco 837 ADSL router running EzVPN remote to get the Authentication Proxy to work? The reason for using the Authentication proxy is that the IOS for the Cisco 837 does not have Individual user Authentication. If so, C...

Hi all,I have a terminal server (TS - ip address 1.1.1.1), where I access to through TACACS+, and that I want to use to connect to the console of a switch (SW).I configured "ip host SW 2033 1.1.1.1" in the TS. When I want to go to the console of the...

I am setting up Auth and Authorization with PIX Firewall. Auth seems to be working fine. but authorization is not working.. The moment I give the commandaaa authorization command TACSERVE, the PIx is locking up and I refer the document http://www.cis...

Hello all.My co-worker and I are trying to get AAA working the way we want it to work with RADIUS ( which may not be possible). The following is the config we have on a 3548 XL switch:aaa new-modelaaa authentication login default group radius locala...

i have problem with dialup,i have a 2600 router which has flash:c2600-i-mz.120-7.T and i am using ACS secure for authentication for our domain users.for normail dialup everything is working fine.but when i am configuring call back for some users its ...

We have a VPN connection through a PIX with IOS 6.2(2). We can get in through the VPN fine and we don't have a problem pinging the servers (ip&domain name) that we need to get to. But when we try and get to them through windows we have a problem get...

I would like to use extended authentication of IPSEC VPN client users on the PIX against ACS for UNIX (v2.3.6) using tacacs. My idea is to implement Network access restriction for specific group on tacacs ACS server - to allow authenticate on the PIX...

Hi, We had recently purchased ACS 3.1 and a few 54mbps wireless AP. Our ACS is installed on W2K Server with Novell Client installed. We were able to get the wireless users to login using the ACS's local database. When we try to set up using external...

Dear allAnyone can help me?i want to setup a counter on my Cisco access registrar to limit the number of hours a dialup user can logon on our network; i.e if the user exeeds the limit of hours, the Radius will disconnect him if he tried to dial one m...

Hello,Does somebody know if it is possible, for a given user, to send differentvalues for the same attribute depending of the requesting NAS ? I would like to assign a particular VLAN on Access Points depending ofusers. But if that user goes on anoth...