Hello, I have an issue with ISE. I see in the license tab that base licenses are over the limit. The active endpoints are a lot fewer Is there sth I could do to fix this?Why is it happening? Thanks and regards, Konstantinos
This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community for Help for other troubleshooting best practices.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community for Help for other troubleshooting best practices.
Forum Posts
Resolved! Upgrade from 2.4 to 2.7/3.0
As the title suggest, as anyone already made the upgrade from version 2.4 to 2.7/3.0 in a production environment? If so did everything went ok?
Resolved! AnyConnect and no policy server detected
Hi Experts, Test environment: ISE 2.3 patch 3 HP Comware switch: Version 7.1.070, Release 3208P03 I am seeing this very weird behavior with AnyConnect. We are using an ACL for posture redirection, so here when I have these two statements: rule 135 ...
Resolved! limit admin access to specific AP group
Dear everyone,My system has WLC, ISE, PI. My operator IT want to manage themselves all the APs that are installed inside their building. On the WLC, we have AP group based on location but I don't know how to limit admin access to a specific AP group....
I am having issues configuring dot1x/mab protocols for my DELL iDRACs. I was hoping to find some support for doing this. I currently have the idracs failing authentication in the RADIUS live logs, meaning that my policy set could be set incorrectly. ...
Hi All I have currently configured this on each switch port:authentication event fail action next-methodauthentication event server dead action authorizeauthentication event server dead action authorize voiceauthentication event server alive action r...
if you configure AUTHENTICATION HOST-MODE MULTI-AUTH on your switch port allowing a single device in the voice domain and multiple devices on the data domain, is it possible to limit the number of devices on the data domain. For example, a single pho...
Can anyone tell me what MIB I need to monitor a ucs-c220-m3. We have inherited these and will look to migrate the ACS application to ISE but in the meantime I need visibility of the device.
So upgraded to 2.7 from 2.4. Guest portal and redirection not working now.Just allows internet access without pop up page.When I run the Portal test URL this fails.The bind is correct to Gi1 but if I change it to Gi0 the test page works but this is...
Hello community, We will Implement Network Access Control with ISE server and EAP-TLS Protocol for Endpoints Authentication using the Windows native client and Machine Certificates generated from the Internal CA of the company (Windows). We also conf...
Hi Guys, I am stuck need help on a solution:- the scenario is as below:- 1. Site 1:- Cisco WLC and Clear Pass --> SSID-Users --> PEAP authentication User2. Site 2:- Cisco WLC and ISE --> SSID-Users --> EAP Authentication (EAP-FAST) user+machine Now i...
Resolved! Unable to Posture MAC OSX
Not sure when this started but we have a few contractors that connect with MAC OSX, when they connect Anyconnect shows the message "Bypassing Anyconnect Scan. Your network is configured to use Cisco NAC agent"The exact policy set works ok with Window...
Hello all, I am having some issues with 802.1x deployment. I When I login into a workstation using my admin account it all goes well. Authentication and authorization works as planned, I get the Dacl from ISE and everyone is happy. The problem is tha...
ISE 2.7MacOSProfileEditor Do anyone know the settings for a MacOS to authc using machine certificate? We are use the profileEditor and try a few options without success. Any help would be appreciated.
