06-01-2003 11:46 PM - edited 03-10-2019 07:19 AM
All,
I'm trying to get callback via ACS to work on my 3620. The call negotiates, initiates call-back (or so it looks like from the logs) and then just sits there. The client never actually receives the callback from the router. I've got an analog callback script in place, I just can't sort out why its not working. I'm sure I've configured something incorrectly or left something out, and I'd appreciate your help.
Debug log:
h: As42 DDR: Authenticated host BLAH with no matching dialer map
3d18h: RADIUS: ustruct sharecount=4
3d18h: Radius: radius_port_info() success=1 radius_nas_port=1
3d18h: RADIUS: Initial Transmit Async42 id 55 x.x.x.x:x, Accounting-Req
est, len 103
3d18h: Attribute 4 6 C0A86901
3d18h: Attribute 5 6 0000002A
3d18h: Attribute 61 6 00000000
3d18h: Attribute 1 20 48415F55
3d18h: Attribute 30 5 30303028
3d18h: Attribute 40 6 00000001
3d18h: Attribute 45 6 00000001
3d18h: Attribute 6 6 00000002
3d18h: Attribute 44 10 30303030
3d18h: Attribute 7 6 00000001
3d18h: Attribute 41 6 00000000
3d18h: RADIUS: Received from id 55 x.x.x.x:x, Accounting-response, len
8
3d18h: Attribute 80 18 736AD98F
3d18h: As42 DDR: PPP callback Callback server starting to BLAH 00000000000
3d18h: TTY42: Async Int reset: Dropping DTR
3d18h: Modem 1/9 Mica: PPP escape_map: Tx map = FFFFFFFF, Rx map = 0
3d18h: RADIUS: ustruct sharecount=3
3d18h: Radius: radius_port_info() success=1 radius_nas_port=1
3d18h: RADIUS: Initial Transmit Async42 id 56 x.x.x.x:x, Accounting-Req
est, len 139
3d18h: Attribute 4 6 C0A86901
3d18h: Attribute 5 6 0000002A
3d18h: Attribute 61 6 00000000
3d18h: Attribute 1 20 48415F55
3d18h: Attribute 30 5 30303028
3d18h: Attribute 40 6 00000002
3d18h: Attribute 45 6 00000001
3d18h: Attribute 6 6 00000002
3d18h: Attribute 44 10 30303030
3d18h: Attribute 7 6 00000001
3d18h: Attribute 49 6 00000010
3d18h: Attribute 42 6 0000002A
3d18h: Attribute 43 6 0000002D
3d18h: Attribute 47 6 00000002
3d18h: Attribute 48 6 00000003
3d18h: Attribute 46 6 00000002
3d18h: Attribute 41 6 00000000
3d18h: RADIUS: Received from id 56 x.x.x.x:x, Accounting-response, len
8
3d18h: Attribute 80 18 447C09E0
3d18h: Modem 1/9 Mica: in modem state TERMINATING
3d18h: Modem 1/9 Mica: in modem state IDLE
3d18h: %ISDN-6-DISCONNECT: Interface Serial0/0:0 disconnected from unknown , c
ll lasted 74 seconds
3d18h: Modem 1/9 Mica: DISCONNECT after 00:01:13, due to reason (0xDF00) Host D
sconnect.
3d18h: TTY42: DSR was dropped
3d18h: tty42: Modem: READY->(unknown)
3d18h: TTY42: dropping DTR, hanging up
3d18h: tty42: Modem: HANGUP->(unknown)
3d18h: Modem 1/9 Mica: PPP escape_map: Tx map = FFFFFFFF, Rx map = 0
3d18h: %LINK-5-CHANGED: Interface Async42, changed state to reset
3d18h: TTY42: cleanup pending. Delaying DTR
3d18h: TTY42: cleanup pending. Delaying DTR
3d18h: TTY42: cleanup pending. Delaying DTR
3d18h: TTY42: no timer type 0 to destroy
3d18h: TTY42: no timer type 1 to destroy
3d18h: TTY42: no timer type 3 to destroy
3d18h: TTY42: no timer type 4 to destroy
3d18h: TTY42: no timer type 2 to destroy
3d18h: Async42: allowing modem_process to continue hangup
3d18h: TTY42: restoring DTR
3d18h: %LINK-3-UPDOWN: Interface Async42, changed state to down
3d18h: As42 DDR: re-enable timeout
3d18h: DDR: callback triggered by dialer_timers
3d18h: As42 DDR: beginning callback to BLAH 000000000000
3d18h: As42 DDR: Attempting to dial 000000000000
3d18h: CHAT42: Attempting async line dialer script
3d18h: CHAT42: Dialing using Modem script: callbackanalog & System script: none
3d18h: DDR: Freeing callback to BLAH 000000000000
3d18h: CHAT42: process started
3d18h: CHAT42: Asserting DTR
3d18h: CHAT42: Chat script callbackanalog started
3d18h: Modem 1/9 Mica: configured for Originate mode, with Null signaling, 0x1
one detection.
3d18h: Modem 1/9 Mica: received dialstring 000000000000
3d18h: Modem 1/9 Mica: in modem state CALL_SETUP
3d18h: %ISDN-6-CONNECT: Interface Serial0/0:29 is now connected to 000000000000
3d18h: Modem 1/9 Mica: in modem state CONNECT
3d18h: Modem 1/9 Mica: in modem state LINK
3d18h: %ISDN-6-CONNECT: Interface Serial0/0:29 is now connected to 000000000000
3d18h: Modem 1/9 Mica: in modem state TRAINUP
3d18h: Modem 1/9 Mica: in modem state EC_NEGOTIATING
06-02-2003 08:21 PM
you can see that the script "callbackanalog" is already started and dialed out and the mica modem is already went all the way to EC_NEGOTIATE that means that the two modems during callback already connected.
Now if the client modem have never received the inbound connection then where did the connection go? Make sure that the number reported in the
3d18h: Modem 1/9 Mica: received dialstring 000000000000
is the number which supposed to be called out during callback for that client modem. Call me have gone some where else. Just verify the number called back and its format. You can turn on "debug isdn q931" to see what numbers are being dialed at isdn layer too.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide