ACS 4.2 GUI Username and password

[Md.Mosharof Hossain]

Hi,

I have setup cisco acs 4.2.1 i windows swerver 2008 and want to access through GUI, GUI interface is appear but I don't know the default  usrname and password. Please help.

Thanks

[Sandeep Choudhary]

HI Hossain,

You can try:

Username  - Admin

Password - Password or password

Setting Up a GUI Administrator Account

http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_server_for_solution_engine/4.2/installation/guide/solution_engine/instalap.html#wp1117461

Resetting the GUI Administrator Login and Password

http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_server_for_solution_engine/4.2/installation/guide/solution_engine/admap.html#wp1141988

Regards

Dont forget to rate helpful posts.

[Md.Mosharof Hossain]

Hi Sandeep choudhary,

Thanks for your reply. I am unable to login using your provided credential. username admin and password--> Password or --> password both i have used but no luck.

[Sandeep Choudhary]

HI Hossain,

Can u try these:

If its ur first time then :

Username: acsadmin

Password: default

After this the server will ask you to change the password. Please give it a try and let me know how it goes.

Reset ACSAdmin Password: To reset the password of the default GUI admin, use the acs reset-password command from the EXEC mode.

http://www.ciscopress.com/articles/article.asp?p=1671906&seqNum=7

Regards

Dont forget to rate helpful posts.

[Md.Mosharof Hossain]

Hi Sandeep choudhary,

I have tried using the below but same result.

Username: acsadmin

Password: default

[Sandeep Choudhary]

Hi Hossain,

so lets find out the exact issue:

Which option did you click (checkbox), windows authentication or local

ACS only while installing ACS?

If u clicked locally then u may need to logon locally to the box first and create an ACS

account.

After installation, I believe you need to use http://127.0.0.1:2002 from the

device CSACS is installed on.

After that, I think you are prompted to setup a local username and

password for administration.

Try using the loopback address, and read the interface carefully for and

guidance on the creation of an admin account.

Regards

Dont forget to rate helpful posts.

[Md.Mosharof Hossain]

Hi Sandeep choudhary,

During the setup i selected "check the ACS internal database only" radio button and finally automatic run http://127.0.0.1:2002 in IE.

[Sandeep Choudhary · Accepted solution]

HI Hossain,

If u clicked locally means:

u must http://localhost:2002  logon locally on which u installed ACS.

u must use one of these HTML browsers:

•Microsoft Internet Explorer 6 Service Pack 1 and 5.5 for Windows-English and Japanese versions

•Microsoft Internet Explorer 7 Service Pack 2 for Windows Server 2003 and Service Pack 2 for Windows XP

•Mozilla Firefox 2.0 and 2.0.0.6

•Netscape Web Browser 7.0, 7.1, and 7.2 for Windows-English and Japanese versions1

Did u foloowed these steps:

http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2/installation/guide/windows/install.html

Regards

[Md.Mosharof Hossain]

Hi Sandeep choudhary,

After using Mozilla Firefox 2.0.0.6 and http://localhost:2002,

Now its working. Many thanks for your help. Previously i was tried from my remote machine.

[Sandeep Choudhary]

Hi Hossain,

Glad that u resolved ur issue.

Thanks for rating.

Reagrds

Dont forget to rate all helpful posts.