cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
864
Views
5
Helpful
3
Replies

CISCO 1117 dialer

ronsametcohen
Beginner
Beginner

Hello .

I down why , but I dont get a ip by the dialer interface .

help please  

 

Interface              IP-Address      OK? Method Status                Protocol
GigabitEthernet0/0/0   10.10.10.1      YES NVRAM  up                    up
GigabitEthernet0/1/0   unassigned      YES unset  up                    up
GigabitEthernet0/1/1   unassigned      YES unset  administratively down down
GigabitEthernet0/1/2   unassigned      YES unset  administratively down down
GigabitEthernet0/1/3   unassigned      YES unset  down                  down
Cellular0/2/0          192.168.124.3   YES IPCP   up                    up
Cellular0/2/1          unassigned      YES NVRAM  administratively down down
ATM0/3/0               unassigned      YES NVRAM  up                    up
Ethernet0/3/0          unassigned      YES NVRAM  down                  down
Dialer1                unassigned      YES NVRAM  up                    up
Controller VDSL 0/3/0 is UP

Daemon Status:          UP

                        XTU-R (DS)              XTU-C (US)
Chip Vendor ID:         'BDCM'                   'IFTN'
Chip Vendor Specific:   0x0000                   0xB206
Chip Vendor Country:    0xB500                   0xB500
Modem Vendor ID:        'CSCO'                   '    '
Modem Vendor Specific:  0x4602                   0x0000
Modem Vendor Country:   0xB500                   0x0000
Serial Number Near:     C1117-4P 16.9.2
Serial Number Far:
Modem Version Near:     16.9.2
Modem Version Far:      0xb206

Modem Status:           TC Sync (Showtime!)
DSL Config Mode:        AUTO
Trained Mode:           G.992.5 (ADSL2+) Annex A

TC Mode:                ATM
Selftest Result:        0x00
DELT configuration:     disabled
DELT state:             not running

Failed full inits:      0
Short inits:            0
Failed short inits:     0

Modem FW  Version:      4.14L.04
Modem PHY Version:      A2pv6F039t.d26d
Modem PHY Source:       System

Line 0:

                        XTU-R (DS)              XTU-C (US)
Trellis:                 ON                      ON
SRA:                     enabled                 enabled
SRA count:               0                       0
Bit swap:                enabled                 enabled
Bit swap count:          15154                   0
Line Attenuation:        24.0 dB                 11.3 dB
Signal Attenuation:      23.0 dB                 11.2 dB
Noise Margin:             9.1 dB                11.0 dB
Attainable Rate:        22436 kbits/s            1148 kbits/s
Actual Power:           20.0 dBm                10.4 dBm
Total FECC:             3964806                  2
Total ES:               513                      2
Total SES:              0                        0
Total LOSS:             0                        0
Total UAS:              480                      480
Total LPRS:             0                        0
Total LOFS:             0                        0
Total LOLS:             0                        0


                  DS Channel1     DS Channel0   US Channel1       US Channel0
Speed (kbps):             NA           18938            NA               918
SRA Previous Speed:       NA               0            NA                 0
Previous Speed:           NA           18941            NA               918
Total Cells:              NA        76390442            NA        1878229804
User Cells:               NA               1            NA                 0
Reed-Solomon EC:          NA         1751049            NA                 0
CRC Errors:               NA             595            NA                 2
Header Errors:            NA             126            NA                 0
Interleave (ms):          NA            7.87            NA              0.23
Actual INP:               NA            2.22            NA              0.03

Training Log :  Stopped
Training Log Filename : flash:vdsllog.bin
interface ATM0/3/0
 no ip address
 atm oversubscribe factor 2
 no atm enable-ilmi-trap
 pvc 8/48
  pppoe-client dial-pool-number 2
 !
!
interface Ethernet0/3/0
 no ip address
 no negotiation auto
!
interface Dialer1
 ip address negotiated
 encapsulation ppp
 dialer pool 2
 ppp mtu adaptive
 ppp pap sent-username xxxx@xxx password 0 xxxxxx
3 Replies 3

balaji.bandi
VIP Community Legend VIP Community Legend
VIP Community Legend

Can you post the full configuration and let us know the ISP provider information?

 

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Georg Pauwen
VIP Master VIP Master
VIP Master

Hello,

 

as far as I recall, if you use PPPoEoA, you need something like this:

 

interface ATM0/3/0
no ip address
atm oversubscribe factor 2
no atm enable-ilmi-trap
pvc 8/48
--> encapsulation aal5mux pppoe-client
pppoe-client dial-pool-number 2

 

If you use PPPoA, you need this:

 

interface ATM0/3/0
no ip address
atm oversubscribe factor 2
no atm enable-ilmi-trap
pvc 8/48
--> encapsulation aal5mux ppp dialer
--> dialer pool-member 2

MHM Cisco World
VIP Mentor VIP Mentor
VIP Mentor

Need encapuslation aal5, trt this and share last status 

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers