cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

cisco CISCO7606-S (R7000) // Temperature

Jairo Osorio
Beginner
Beginner

Hi all,

When I check the output for the command "show environment temperature all" I see high temperatures reading, is this ok ?? 

router#show environment temperature all 
  module 1 outlet temperature: 53C
  module 1 inlet temperature: 34C
  module 2 outlet temperature: 57C
  module 2 inlet temperature: 31C
  module 2 device-1 temperature: 32C
  module 2 device-2 temperature: 54C
  module 3 outlet temperature: 55C
  module 3 inlet temperature: 32C
  module 3 device-1 temperature: 32C
  module 3 device-2 temperature: 51C
  module 4 outlet temperature: 50C
  module 4 inlet temperature: 34C
  module 5 outlet temperature: 33C
  module 5 inlet temperature: 32C
  module 5 device-1 temperature: 31C
  module 5 device-2 temperature: 33C
  module 6 outlet temperature: 38C
  module 6 inlet temperature: 34C
  module 6 device-1 temperature: 43C
  module 6 device-2 temperature: 42C
  module 6 asic-1 (SSO-1) temp: 33C
  module 6 asic-2 (SSO-2) temp: 33C
  module 6 asic-3 (SSO-3) temp: 33C
  module 6 asic-4 (SSO-4) temp: 33C
  module 6 asic-5 (SSA-1) temp: 33C
  module 6 asic-6 (HYPERION-1) temp: 33C
  module 6 RP outlet temperature: 35C
  module 6 RP inlet temperature: 36C
  module 6 EARL outlet temperature: 39C
  module 6 EARL inlet temperature: 31C

 

4 REPLIES 4

AFROJ AHMAD
Cisco Employee
Cisco Employee

Hi,

the above output is correct  , the above command will show you the "temprature " for all the modules ,rp and backplane ...

 


Router#show environment temperature ?
  all        selects all FRU-types
  backplane  specify backplane
  earl       specify earl <slot>
  module     specify module location
  rp         specify RP (MSFC) <slot>
  vdb        specify vdb <slot>
  vtt        specify VTT <number>
  |          Output modifiers
  <cr>

 
If you want to see the "temp" for only RP  then run the below command::


Router#show environment temperature rp ?
  <1-4>  module slot number

 

Thanks-

Afroz

***Ratings Encourages Contributors ***

 

Thanks- Afroz [Do rate the useful post] ****Ratings Encourages Contributors ****

Hi afrahmad, this command only gave me the temperature for module 6, and is the same than previous command 

 

router#show environment temperature rp 1
router#show environment temperature rp 2
router#show environment temperature rp 3
router#show environment temperature rp 4
router#show environment temperature rp 5
router#show environment temperature rp 6
  module 6 RP outlet temperature: 35C
  module 6 RP inlet temperature: 36C

 

router#show environment                 
environmental alarms:
  no alarms

backplane: 
  operating clock count: 2
  
fan-tray 1: 
  fan-tray 1 type: FAN-MOD-6SHS
  fan-tray 1 mode: Auto
  fan-tray 1 fan-fail: OK
clock 1: 
  clock 1 OK: OK, clock 1 clock-inuse: in-use
clock 2: 
  clock 2 OK: OK, clock 2 clock-inuse: not-in-use
power-supply 1: 
  power-supply 1 fan-fail: OK
  power-supply 1 power-input: 2 DC active
  power-supply 1 power-output-mode: high
  power-supply 1 incompatible with fan: OK
  power-supply 1 power-output-fail: OK
power-supply 2: 
  power-supply 2 fan-fail: OK
  power-supply 2 power-input: 2 DC active
  power-supply 2 power-output-mode: high
  power-supply 2 incompatible with fan: OK
  power-supply 2 power-output-fail: OK
module 1: 
  module 1 power-output-fail: OK
  module 1 outlet temperature: 52C
  module 1 inlet temperature: 34C
module 2: 
  module 2 power-output-fail: OK
  module 2 outlet temperature: 56C
  module 2 inlet temperature: 31C
  module 2 device-1 temperature: 32C
  module 2 device-2 temperature: 54C
module 3: 
  module 3 power-output-fail: OK
  module 3 outlet temperature: 55C
  module 3 inlet temperature: 32C
  module 3 device-1 temperature: 32C
  module 3 device-2 temperature: 51C
module 4: 
  module 4 power-output-fail: OK
  module 4 outlet temperature: 49C
  module 4 inlet temperature: 33C
module 5: 
  module 5 power-output-fail: OK
  module 5 outlet temperature: 33C
  module 5 inlet temperature: 32C
  module 5 device-1 temperature: 31C
  module 5 device-2 temperature: 33C
module 6: 
  module 6 power-output-fail: OK
  module 6 outlet temperature: 38C
  module 6 inlet temperature: 34C
  module 6 device-1 temperature: 42C
  module 6 device-2 temperature: 42C
  module 6 asic-1 (SSO-1) temp: 33C
  module 6 asic-2 (SSO-2) temp: 33C
  module 6 asic-3 (SSO-3) temp: 33C
  module 6 asic-4 (SSO-4) temp: 33C
  module 6 asic-5 (SSA-1) temp: 33C
  module 6 asic-6 (HYPERION-1) temp: 33C
  module 6 RP outlet temperature: 35C
  module 6 RP inlet temperature: 36C

  module 6 EARL outlet temperature: 39C
  module 6 EARL inlet temperature: 30C

can you explain what you are looking for.. as the command is showing you the output the way is should be..

 

Thanks-
 

Thanks- Afroz [Do rate the useful post] ****Ratings Encourages Contributors ****

Hi afrahmad I want to know if the temp output is ok for all modules, because 53C seems to be high for the router... 

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: