Network Management

Resolved! Configuration change logs with EEM

Hi,I am trying to log all commands executed on the Cisco Router. And it is working fine. However it wont show who executed the commands. It just shows command was executed *Nov 15 00:38:56.356: %HA_EM-6-LOG: cli-match: configure terminal Command Exe...

MAC Address

Hi,I am wondering if there is a way to find out the exact model of a cisco product by its MAC Address? I have a Cisco product showing up on my works network that I cannot find the actual device. When I look up the MAC address it just tells me its Cis...

Resolved! Which ports are used by LMS 4.2.5 Software Center

Hi everybody!we are trying to download device updates and packages via the software center of lms 4.2.5. but get the attached error msg.Which ports are used for the download (for firewall configuration)I can't find the used ports for this function in...

Fetch VLAN on multiple Devices

Hi everybody, I'm searching actually how to fetch VLAN on my Network Infrastructure (Switch). I want to view a specific VLAN on all my switchs; it's possible ? Thanks at all !

Default Username and Password not Working after "write erase" and reload

I was instructed to "write erase" and reload before beginning the initial configuration of a new Cisco 2900 router. When I connected via console, the default username and password "cisco" "cisco" worked. So I issued write erase and then reloaded. Aft...

ISA 500

Is there a possiility to script the Firewall-Configuration for Backup or for editing the configuration and restoring it to get productive?

Resolved! Supress Syslog Output for EEM Policy and write directly to remote FTP

I've got a slightly modified version of the handy findmyrouter.tcl script running on my 819G - but I'd like some assistance to make some tweaks to how it is working. The original script can be found here:https://supportforums.cisco.com/document/1201...

Using LMS to extract VRF name as a variable from device config to deploy VRF name in additional configuration

Using LMS is there a way to run a job which would extract the VRF name in part of the configuration and then use it as a variable to deploy additional configuration using the VRF name. We have a number of management VRF's and need to deploy a mass co...

Resolved! Ask The Expert: Understanding, Implementing, and Troubleshooting Cisco Prime Network

Ask questions and learn about Cisco Prime Network with Cisco experts Vignesh Rajendran Praveen and Jaminder Singh Bali.Cisco Prime Network is and Cisco Prime Network provides cost-effective device operation, administration and network fault manageme...

EEM script that generates only 1 email when a fxs port is offhook.

Using the below config I am able to receive a email anytime my voice port is in any other state than ON HOOK. The problem I have is the script runs every 30 seconds and I receive an email every 30 seconds the line is in any other state than "ON-HOOK...

Resolved! EEM Script is not removing the disable port from suspend_port.dat by seeing syslog port up message

Dears, I am trying to disable the inactive port by using your provided script sl_suspend_ports.tcl and tm_suspend_ports.tcl. I am using a cisco 3560 8 port switch with below scenario. All the switch ports are admin enabeld and not in connected state....

Comparing NX-OS Configurations in Cisco Prime 2.1 or LMS 4.2.5

Hello All,Maybe this is just an NX-OS thing but does anyone have issues comparing different versions of a configuration for the same device? As an example we have Nexus 5548 running version 5.1(3)N2(1). When someone configures an interface on the s...

New to EEM, i wanna soft reset BGP when a prefix list is applied

Hello, This is my script: event manager applet SOFTRESETBGP_IN event cli pattern "neighbor 10.0.0.2 prefix-list.* in" sync no skip no period 1 action 1.0 cli command "do clear ip bgp 10.0.0.2 soft in" action 2.0 syslog msg "BGP PEERS SOFT RESETED IN"...

Resolved! EEM $_ipsla_condition variable states

I am trying to build an EEM applet on a 3850 switch that will shut a port off when an sla echo times out and no shut's the port when the sla starts receiving a reply. My problem is I don't believe that I am checking the right state in my if logic bec...

EEM script to monitor and shut / no shut fxo port

Development team,I've run into a situation with a large hospital UC deployment that I'm looking to an EEM or TCL solution for. I have a Valcom paging integration to a pair of FXO ports on two 3945 ISR G2s. Ocasionally, and without any forensic deta...

Network Management

Forum Posts

Resolved! Configuration change logs with EEM

MAC Address

Resolved! Which ports are used by LMS 4.2.5 Software Center

Fetch VLAN on multiple Devices

Default Username and Password not Working after "write erase" and reload

ISA 500

Resolved! Supress Syslog Output for EEM Policy and write directly to remote FTP

Using LMS to extract VRF name as a variable from device config to deploy VRF name in additional configuration

Resolved! Ask The Expert: Understanding, Implementing, and Troubleshooting Cisco Prime Network

EEM script that generates only 1 email when a fxs port is offhook.

Resolved! EEM Script is not removing the disable port from suspend_port.dat by seeing syslog port up message

Comparing NX-OS Configurations in Cisco Prime 2.1 or LMS 4.2.5

New to EEM, i wanna soft reset BGP when a prefix list is applied

Resolved! EEM $_ipsla_condition variable states

EEM script to monitor and shut / no shut fxo port

From Hope to Strategy: Elevating Campus Network Reliability

Cisco Flexible NetFlow (FNF) v9 Working with PRTG (Gibraltar 16.12.13)

How to convert string with spaces to URL encoding in EEM scripting!

Cannot get model-driven telemetry to work on ASR9K, IOS XR 7.11.2

ALMA LINUX 9 On-Prem License Manager UI admin password Recovery

ACL TO INTERNET

SNMP questions for gurus in this Network Management forum

Can I use normal ethernet port (1-48) as uplink?

Firepower vFMC 76.2 Wildcard FQDN objects?

PublicKey authentication on router, but Ansible still uses password