819
Views
0
Helpful
2
Replies
IOS push failing from RME
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-06-2011 06:00 PM
Was in the middle of the IOS push on the switches and encounter one problem and i.e. on every switch I am receiving the error i.e. Device running-config is modified but failed to save the running-config to startup-config.Cause: TELNET: Failed to establish TELNET connection to 10.x.x.x -
Cause: Authentication failed on device 3 times.
Could not detect SSH protocols running on the device
And I am sure telnet is working becasue we run the NETCONFIG job first to put the SNMP RW community on the device.
Cause: Authentication failed on device 3 times.
Could not detect SSH protocols running on the device
And I am sure telnet is working becasue we run the NETCONFIG job first to put the SNMP RW community on the device.
Note:- We are pushing the .tar file and all the below switches were 3560 24/48 ports
Below is the output of the Job
-----------------------------------------------------------------------------------------------
JOB ID - 1111 SUMMARY
---------------------------------------------
Device Name : sss-1
Software upgrade result - Failed
Total number of devices scheduled for upgrade : 12
Number of devices upgraded : 0
Number of devices failed : 12 (All 12 devices has the same error)
Total time taken for Job - 22 Minutes 21 Seconds
Status of Job - FAILED
-----------------------------------------------------------------------------------------------
Starting Job: ID - 1835
Job Started At : Thu Jan 06 20:00:00 EST 2011
Job running on : xxxxxxxxxxxxxx
Upgrade Mode : Parallel
Reboot Mode : Parallel
Protocol Order for Image Transfer : TFTP
Protocol Order for Config-operations : TELNET,SSH
Total number of device(s) to be processed : 12
Job started.
Processing Device : sss-1
Start Time : Thu Jan 06 20:00:12 EST 2011
Device is locked for exclusive access.
The supported protocols for image transfer are: TFTP
Connecting to the device using TELNET...
Connected successfully.
Going to perform delete operation based on the patterns in the List [.*\.bin, html, snmp, help, .*\.tar]
Files that will be excluded from deletion are: [vlan\.dat, config\.text, config\.txt, private-config\.text, private-config\.txt, multiple-fs, env_vars, system_env_vars, info\.ver, info]
Storage from which files are to be deleted is: flash
Available Flash files: vlan.dat,config.text,c3560-ipbase-mz.122-35.SE5,private-config.text,
vlan.dat -> will be excluded from deletion. File matched with the pattern: "vlan\.dat"
config.text -> will be excluded from deletion. File matched with the pattern: "config\.text"
c3560-ipbase-mz.122-35.SE5 -> Doesn't match with the patterns in the delete list.
private-config.text -> will be excluded from deletion. File matched with the pattern: "private-config\.text"
Unable to get the needed space by deleting the files in deleteList.
Going to perform delete operation leaving the files that match the patterns in the excludeList: [vlan\.dat, config\.text, config\.txt, private-config\.text, private-config\.txt, multiple-fs, env_vars, system_env_vars, info\.ver, info]
Storage from which files are to be deleted is: flash
Available Flash files: vlan.dat,config.text,c3560-ipbase-mz.122-35.SE5,private-config.text,
vlan.dat -> will be excluded from deletion. File matched with the pattern: "vlan\.dat"
config.text -> will be excluded from deletion. File matched with the pattern: "config\.text"
c3560-ipbase-mz.122-35.SE5-> deleted
private-config.text -> will be excluded from deletion. File matched with the pattern: "private-config\.text"
Obtained sufficient free space after deletion.Proceeding with distribution operation
Retrieving configuration file from the device...
Current device config is copied to C:\PROGRA~2\CSCOpx\files\rme\jobs\swim\1835\dot-168-swi-10_Config
Checking if HTTP server is enabled on the device...
Http Server is not enabled, will continue with Software Upgrade Operation.
Copying c3560-ipbasek9-tar.122-53.SE1.tar from Software Repository to tftp-specific directory.
Copied successfully to C:/PROGRA~2/CSCOpx/tftpboot/rep_sw_7285416869829389325
Loading image file to flash device : rep_sw_7285416869829389325 --> flash:c3560-ipbasek9-tar.122-53.SE1.tar using TFTP
Loading image file to flash device is completed.
Total time for copying the image - 15 Minutes 30 Seconds
Updating config file during software upgrade process
Device running-config is modified but failed to save the running-config to startup-config.Cause: TELNET: Failed to establish TELNET connection to 10.137.240.10 -
Cause: Authentication failed on device 3 times.
Could not detect SSH protocols running on the device
Device is unlocked.
Device Upgrade Result : Failed
End Time:Thu Jan 06 20:18:45 EST 2011
JOB ID - 1111 SUMMARY
---------------------------------------------
Device Name : sss-1
Software upgrade result - Failed
Total number of devices scheduled for upgrade : 12
Number of devices upgraded : 0
Number of devices failed : 12 (All 12 devices has the same error)
Total time taken for Job - 22 Minutes 21 Seconds
Status of Job - FAILED
-----------------------------------------------------------------------------------------------
Starting Job: ID - 1835
Job Started At : Thu Jan 06 20:00:00 EST 2011
Job running on : xxxxxxxxxxxxxx
Upgrade Mode : Parallel
Reboot Mode : Parallel
Protocol Order for Image Transfer : TFTP
Protocol Order for Config-operations : TELNET,SSH
Total number of device(s) to be processed : 12
Job started.
Processing Device : sss-1
Start Time : Thu Jan 06 20:00:12 EST 2011
Device is locked for exclusive access.
The supported protocols for image transfer are: TFTP
Connecting to the device using TELNET...
Connected successfully.
Going to perform delete operation based on the patterns in the List [.*\.bin, html, snmp, help, .*\.tar]
Files that will be excluded from deletion are: [vlan\.dat, config\.text, config\.txt, private-config\.text, private-config\.txt, multiple-fs, env_vars, system_env_vars, info\.ver, info]
Storage from which files are to be deleted is: flash
Available Flash files: vlan.dat,config.text,c3560-ipbase-mz.122-35.SE5,private-config.text,
vlan.dat -> will be excluded from deletion. File matched with the pattern: "vlan\.dat"
config.text -> will be excluded from deletion. File matched with the pattern: "config\.text"
c3560-ipbase-mz.122-35.SE5 -> Doesn't match with the patterns in the delete list.
private-config.text -> will be excluded from deletion. File matched with the pattern: "private-config\.text"
Unable to get the needed space by deleting the files in deleteList.
Going to perform delete operation leaving the files that match the patterns in the excludeList: [vlan\.dat, config\.text, config\.txt, private-config\.text, private-config\.txt, multiple-fs, env_vars, system_env_vars, info\.ver, info]
Storage from which files are to be deleted is: flash
Available Flash files: vlan.dat,config.text,c3560-ipbase-mz.122-35.SE5,private-config.text,
vlan.dat -> will be excluded from deletion. File matched with the pattern: "vlan\.dat"
config.text -> will be excluded from deletion. File matched with the pattern: "config\.text"
c3560-ipbase-mz.122-35.SE5-> deleted
private-config.text -> will be excluded from deletion. File matched with the pattern: "private-config\.text"
Obtained sufficient free space after deletion.Proceeding with distribution operation
Retrieving configuration file from the device...
Current device config is copied to C:\PROGRA~2\CSCOpx\files\rme\jobs\swim\1835\dot-168-swi-10_Config
Checking if HTTP server is enabled on the device...
Http Server is not enabled, will continue with Software Upgrade Operation.
Copying c3560-ipbasek9-tar.122-53.SE1.tar from Software Repository to tftp-specific directory.
Copied successfully to C:/PROGRA~2/CSCOpx/tftpboot/rep_sw_7285416869829389325
Loading image file to flash device : rep_sw_7285416869829389325 --> flash:c3560-ipbasek9-tar.122-53.SE1.tar using TFTP
Loading image file to flash device is completed.
Total time for copying the image - 15 Minutes 30 Seconds
Updating config file during software upgrade process
Device running-config is modified but failed to save the running-config to startup-config.Cause: TELNET: Failed to establish TELNET connection to 10.137.240.10 -
Cause: Authentication failed on device 3 times.
Could not detect SSH protocols running on the device
Device is unlocked.
Device Upgrade Result : Failed
End Time:Thu Jan 06 20:18:45 EST 2011
Labels:
- Labels:
-
Network Management
2 Replies 2
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-08-2011 02:48 AM
Not sure why it says that. According to the log the image distribution itself went fine.
You could now create a second job to sync the running conf to the startup. Or use the out-of-sync report to launch a sync
And a third job to restart the devices to use the new image if you are sure all is fine.
You may want to post the 1835.log as a zip file to look further into this.
Cheers,
Michel
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-03-2013 10:40 AM
So what actually failed? I get these issues sometimes as well. OP have you figured it out yet?
