05-23-2008 11:02 AM
1-I have remote sites and main branch connection between remote sites to main branch is MPLS
2-Connection between main branch to remote sites over 2 ISP
My question
I need real time monitor with out enable GRE tunnel between main branch to remote site
If the router down in remote site from any ISP I need the router will be reed
I need this action in topology map
I don't need this action by mail or by syslog
Solved! Go to Solution.
05-27-2008 11:07 AM
i need to monitor the up devices do u understand me
05-27-2008 11:19 AM
DFM monitors all devices in a Known state. If the devices are healthy (e.g. they are reachable, and have no down interfaces) then you will not see any alert for them in AAD. DFM is still managing and monitor those devices, though.
05-27-2008 12:02 PM
Joe
If core switch have sub interfaces connected to remote sites. And I will but this core switch in critical poller if any router down in remote sites the link between sub interfaces from core switch to router in remote sites will be down in topology map
05-27-2008 12:27 PM
If a link that exists on the topology map goes down according to SNMP (i.e. the ifOperStatus is down), then the topology map should reflect this after the next polling cycle.
05-28-2008 09:24 AM
Joe
1- I take for you screen shot for problem in DFM the bandwidth is 2M but ciscoworks get the bandwidth 256 and get me alert about utilization why .these problem form 14 day tell know
2- I make hosts file and put it in C:\WINDOWS\system32\drivers\etc and restart the server and run discovery and run data collection but the device not appear with name
05-28-2008 09:32 AM
You should check ifSpeed for this interface to make sure it is advertising the 2 Mbps value.
You will need to remove and re-add devices from DFM to get the name updates.
05-28-2008 09:32 AM
05-28-2008 10:35 AM
1-How I can check ifSpeed I need steps
2-You will need to remove and re-add devices from DFM to get the name updates.
This Is will help me in all application like CM, RME, IP or I will remove devices from all application
05-28-2008 11:31 AM
How I can enable cdp over mpls between to site to discover this site by Cisco works
05-28-2008 11:34 AM
I do not believe this is possible. However, the typical way to enable CDP on a non-broadcast interface is to add the command "cdp enable".
05-28-2008 11:33 AM
Perform an snmpwalk of ifSpeed on this device. Then perform an snmpwalk for ifDescr. Match the ifIndex values to confirm the ifSpeed value.
No, this will help for DFM. For other applications, you will need to modify the devices' display names in DCR, or configure Discovery to "Update DCR Display Name" under Common Services > Device Discovery > Discovery Settings > Global Settings. Then you will need to run another Discovery.
05-28-2008 09:43 PM
Joe I don't understand about how I can Perform an snmpwalk of ifSpeed on this device . did you mean I will enter to device and Right snmpwalk
And I don't under stand this also Then perform an snmpwalk for ifDescr how I can make this
05-29-2008 02:16 AM
05-29-2008 08:54 AM
What does show cdp neighbor report on each end of the link? Just because you can enable CDP doesn't mean it will actually work.
05-29-2008 12:21 PM
What does show cdp neighbor report on each end of the link?
In branch just I see direct connected device from my network put in wan interface I see the router from ISP
In remote site I see the connected switch from my site put in wan serial interface I didn't see any thing
Joe please tell me what can do. To do I need Cisco works drown the link I need solution
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide