06-29-2010 06:55 AM
Hi All
I have Cisco 7609 with 7600-sip-400 and 7600-sip-200 cards.
I see these cards on CiscoView chassis,
but I cannot see the subslot interface card LED status on SIP-400 but on SIP-200 i can see green led for active port status.
The card are:
NAME: "module 8", DESCR: "Cisco 7600 Series SPA Interface Processor-400 Rev. 2."
PID: 7600-SIP-400 , VID: V08, SN: JAE1340K72E
NAME: "SPA subslot 8/0", DESCR: "2-port Gigabit Ethernet Shared Port Adapter"
PID: SPA-2X1GE , VID: V02, SN: JAE1338JC4P
NAME: "subslot 8/0 transceiver 0", DESCR: "GE LX"
PID: SFP-GE-L , VID: B , SN: FNS135102U5
I download the latest package of Cat6000IOS v30.2
and the readme says:
Says there interface modules are supported:
SHARED PORT ADAPTERS SUPPORTED BY 7600-SIP-400 MODULE
* SPA-4XOC3-POS --> IOS Release 12.2(33)SRA or later
* SPA-2XOC3-POS --> IOS Release 12.2(33)SRA or later
* SPA-1XOC12-POS --> IOS Release 12.2(33)SRA or later
* SPA-4XOC3-ATM --> IOS Release 12.2(33)SRA or later
* SPA-2XOC3-ATM --> IOS Release 12.2(33)SRA or later
* SPA-1XOC12-ATM --> IOS Release 12.2(33)SRA or later
* SPA-2X1GE --> IOS Release 12.2(33)SRA or later
Cisco 7609 SIP-400 module fm ver. is 12.2(33)SRD4 which is supported i think,
Please suggest how to troubleshoot it ?
Regards
Gautam
07-04-2010 10:43 AM
Hi All,
Require urgent support on this, can someone look into this ?
07-05-2010 12:20 AM
Post a screenshot illustrating the problem.
07-05-2010 04:20 AM
07-05-2010 10:43 AM
There are no recent reports of problems here, but the symptoms match an older bug, CSCsk75156 which should have been fixed in Cat6000IOS package 29.0. Post the output of "DIR NMSROOT/MDC/tomcat/webapps/CVng/WEB-INF/classes/com/cisco/nm/cvw/devpkgs".
07-21-2010 01:47 AM
07-21-2010 08:51 PM
I wanted the textual output of the DIR command from the DOS shell. This output will contain the file sizes.
07-22-2010 01:06 AM
07-22-2010 09:59 PM
The package sizes look correct, and it looks like the count is right. I recommend you open a TAC service request so development can take a look at this.
07-22-2010 10:09 PM
Hi Joe,
I would like to try something else before we open TAC case, kindly suggest some alternative for troubleshooting.
Is it possible to downgrade the CV device packages for Cat6000IOS to ver. 29 from ver. 30.2. ?
07-22-2010 10:12 PM
You would need to restore a package repository which had all of the interdependent packages. It is not as simple as replacing the current Cat6000IOS package with an older version. There's not much more that can be done for troubleshooting at this point. The LED thing should have been fixed. I suspect a regression, but I do not have device package code, so I cannot confirm myself.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide