cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
936
Views
0
Helpful
8
Replies
meet_mkhan
Beginner

Problem with ip address in L3 switch port

Hi Experts,

I am getting error when trying to give ip address to 3550 switch interfcae

check below error

SW-3500(config)#

SW-3500(config)#int fa0/7

SW-3500(config-if)#no swi

SW-3500(config-if)#no switchport mo

SW-3500(config-if)#no switchport mode

SW-3500(config-if)#no switchport acce

SW-3500(config-if)#no switchport access vla

SW-3500(config-if)#no switchport access vlan

SW-3500(config-if)#ip address 1.1.1.1 255.0.0.0

                   ^

% Invalid input detected at '^' marker.

SW-3500(config-if)#^Z

SW-3500#

00:15:38: %SYS-5-CONFIG_I: Configured from console by consolesh ver

SW-3500#sh version

Cisco Internetwork Operating System Software

IOS (tm) C3500XL Software (C3500XL-C3H2S-M), Version 12.0(5.2)XU, MAINTENANCE IN

TERIM SOFTWARE

Copyright (c) 1986-2000 by cisco Systems, Inc.

Compiled Mon 17-Jul-00 18:29 by ayounes

Image text-base: 0x00003000, data-base: 0x00301F3C

ROM: Bootstrap program is C3500XL boot loader

SW-3500 uptime is 15 minutes

System returned to ROM by power-on

System image file is "flash:c3500XL-c3h2s-mz-120.5.2-XU.bin"

cisco WS-C3524-XL (PowerPC403) processor (revision 0x01) with 8192K/1024K bytes

of memory.

Processor board ID FAA0502M1GG, with hardware revision 0x00

Last reset from power-on

Processor is running Enterprise Edition Software

Cluster command switch capable

Cluster member switch capable

24 FastEthernet/IEEE 802.3 interface(s)

2 Gigabit Ethernet/IEEE 802.3 interface(s)

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 00:04:C1:C1:F1:C0

Motherboard assembly number: 73-3904-11

Power supply part number: 34-0851-02

Motherboard serial number: FAB0501B21D

Power supply serial number: PHI044502HF

Model revision number: A0

Model number: WS-C3524-XL-EN

System serial number: FAA0502M1GG

Configuration register is 0xF

SW-3500#

2 ACCEPTED SOLUTIONS

Accepted Solutions
shajakhan85
Beginner

Hi,

3524 switch does not support L-3 functionality.

Regards,

Shajakhan.K

View solution in original post

In your original post is output from show version and it is quite clear that this switch is a 3524

cisco WS-C3524-XL (PowerPC403) processor (revision 0x01) with 8192K/1024K bytes

of memory.

HTH

Rick

HTH

Rick

View solution in original post

8 REPLIES 8
Rejohn Cuares
Enthusiast

Enter "no switchport" under an interface.

Sent from Cisco Technical Support iPhone App

Please rate replies and mark question as "answered" if applicable.

Hi,

         Thanks for your soon reply i appied no switchport

               but it is incomplete coomand.Please check below config

SW-3500(config-if)#no switchport

% Incomplete command.

SW-3500(config-if)#no switchport ?

  access    Set access mode characteristics of the interface

  mode      Set trunking mode of the interface

  multi     Set characteristics when in multi-VLAN mode

  priority  Set 802.1p priorities

  trunk     Set trunking characteristics of the interface

  voice     Voice appliance attributes

shajakhan85
Beginner

Hi,

3524 switch does not support L-3 functionality.

Regards,

Shajakhan.K

Hi,

     I am dealing with 3550 switch and its L3 switch

In your original post is output from show version and it is quite clear that this switch is a 3524

cisco WS-C3524-XL (PowerPC403) processor (revision 0x01) with 8192K/1024K bytes

of memory.

HTH

Rick

HTH

Rick

Sorry i dint check properly so what is the solutin for it ?can i change ios to assign ip address.

This question was also posted in another forum and in that forum we have provided the answer that it is a limitation of the switch. So changing IOS would not provide a solution. The solution is to use a different switch which does have support for layer 3 processing.

HTH

Rick

HTH

Rick

Thanks guys for reply and all is extremely helpful.