11-06-2015 04:14 AM - edited 03-11-2019 11:50 PM
Hi,
Not sure if this is a bug with ASDM, but when I try to add a virtual interface through ASDM I receive the following error when clicking 'Apply'...
"With the current license device will only supports 2 fully functional interfaces. Third interface can be added, but the traffic from this interface to another interface need to be blocked. Please make appropriate selection in the advanced tab"
(By the way, the above message has been translated word for word, and yes, the use of English is terrible!!)
However, if use good old CLI, it works fine:
FW1(config)# int redundant 1.101
FW1(config-subif)# vlan 101
FW1(config-subif)# security-level 100
FW1(config-subif)# ip address 10.100.1.65 255.255.255.224
FW1(config-subif)# nameif Management
FW1(config-subif)# no shut
The ASA is running the Security Plus license, so I should have unlimited interfaces? I only have a few VLANs. Result of 'Show Ver' below...
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited perpetual
Maximum VLANs : 30 perpetual
Inside Hosts : Unlimited perpetual
Failover : Active/Standby perpetual
Encryption-DES : Enabled perpetual
Encryption-3DES-AES : Enabled perpetual
GTP/GPRS : Disabled perpetual
AnyConnect Premium Peers : 4 perpetual
AnyConnect Essentials : Disabled perpetual
Other VPN Peers : 50 perpetual
Total VPN Peers : 50 perpetual
Shared License : Disabled perpetual
AnyConnect for Mobile : Disabled perpetual
AnyConnect for Cisco VPN Phone : Disabled perpetual
Advanced Endpoint Assessment : Disabled perpetual
Total UC Proxy Sessions : 160 perpetual
Botnet Traffic Filter : Disabled perpetual
Cluster : Disabled perpetual
ASA is running 9.5(1); ASDM is running 7.5(1)
I presume this is just another issue with ASDM?
Thanks for your time.
Solved! Go to Solution.
11-06-2015 04:31 AM
Hi Tony,
This issue is tracked under defect id : CSCuw09242
Refer the link:
https://tools.cisco.com/bugsearch/bug/CSCuw09242/?reffering_site=dumpcr
Hope it helps!!!
Thanks,
R.Seth
Mark the answer as correct if it helps in resolving your query!!!
11-06-2015 04:31 AM
Hi Tony,
This issue is tracked under defect id : CSCuw09242
Refer the link:
https://tools.cisco.com/bugsearch/bug/CSCuw09242/?reffering_site=dumpcr
Hope it helps!!!
Thanks,
R.Seth
Mark the answer as correct if it helps in resolving your query!!!
11-06-2015 04:35 AM
Thanks Rishabh.
Though I'm not quite sure why the status is showing as Fixed?
At least I know nothing's wrong with the config!
Tony
11-06-2015 04:51 AM
Hi Tony,
The fix should be integrated in next release of ASDM as we can see that the bug is already fixed.
You can save the bug so that you can get automatic updates regarding fixed version.
HTH.
R. Seth
11-07-2015 06:40 AM
hello
i have the SAME issue with ASDM 7.5 on asa 5506x . the cli is fine. the gUI blocks me. t see the screen capture. i agree that the english is not proper on the error message
Cisco Adaptive Security Appliance Software Version 9.5(1)
Device Manager Version 7.5(1)
System image file is "disk0:/asa951-lfbff-k8.spa"
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited perpetual
Maximum VLANs : 30 perpetual
Inside Hosts : Unlimited perpetual
Failover : Active/Standby perpetual
Encryption-DES : Enabled perpetual
Encryption-3DES-AES : Enabled perpetual
GTP/GPRS : Disabled perpetual
AnyConnect Premium Peers : 4 perpetual
AnyConnect Essentials : Disabled perpetual
Other VPN Peers : 50 perpetual
Total VPN Peers : 50 perpetual
Shared License : Disabled perpetual
AnyConnect for Mobile : Disabled perpetual
AnyConnect for Cisco VPN Phone : Disabled perpetual
Advanced Endpoint Assessment : Disabled perpetual
Total UC Proxy Sessions : 160 perpetual
Botnet Traffic Filter : Disabled perpetual
Cluster : Disabled perpetual
This platform has an ASA 5506 Security Plus license.
Serial Number: <removed>
Running Permanent Activation Key: <removed>
Configuration register is 0x1
Image type : Release
Key Version : A
Configuration last modified by <remived> at 22:26:15.039 EST Fri Nov 6 2015
11-07-2015 07:08 AM
i have ASDM 7.5(1)
i see that on 15 oct asdm 7.5(1) 90
i tried and it does NOT fix the issue
aslo . if i go back to asdm 7.4(3) will the issue be fixed?
will it still support firepower?
please advise
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide