This is my first Cisco setup. Local workstations get ip address but cannot get out to the internet. Can someone look over my running config? Building configuration... Current configuration : 4318 bytes ! ! Last configuration change at 12:29:28 ...
Forum Posts
Hi All Following the advisory detailed below does anyone at Cisco know if this affects FTD in passive mode? I presume it doesn't as it isn't actively managing the SIP connections however nothing is mentioned in the advisory. https://tools.cisco.com...
Hi I have some trouble creating a "trunk" on the ASA5506-x-w. On the old 5505 easy switchport trunk etc.. but on the 5506 with sub-interfacec, i have a hard time to get my setup working, (simple setup)and is a bit embarrassed that i have to ask for ...
Hi Folks, I have alot of dns failed/timeout messages from my firewall when its processing FQDN rules. These timeouts are always for low TTL sites, like ocws.officeapps.live.com for eg. I'm using the default dns expiry (1 minute). And I can lift this ...
Resolved! USB on ASA5585-X
Hi, folks.I know Cisco ASA5585-X support external USB as disk1, I have one ASA 5585-X SSP-40 running 9.1 but somehow it cannot recognize 8G FAT32 USB as disk1. Do I miss anything? thanks.Leo
NOTE: IP and other information posted has been changed from actual config... I have a firewall where ASDM put in the following statement when somebody was setting up/configuring the firewall. asdm location 192.168.0.0 255.255.255.0 outside Howe...
Resolved! Unable to launch ASDM
Seeking guidance since I have not been able to resolve this problem. I can SSH to the firewall without any problems. The firewall (ASA 5520) is currently running 8.4(3).3 and I've tried with ASDM images asdm-647.bin and asdm-781-150.bin # dir disk0...
Hey Guys, So I use an ASA FW 5515x. On this, I NAT'ed my Exchange Server out, specifying the ports also. More like a PAT. However, I am unable to ping the public IP (Outside Address) of the Exchange Server from outside. Traceroute works. Hits it. ...
Hi all, As per subject. Is it possible to GET the 'real' / hardware serial number for each managed device using the API? (From CLI you would get this with the "show inventory" command) My FMCs manages over 100 sensors so I would rather not do t...
Hi. I have some queries using the ASA 5506-x in transparent mode. I wish to use the ASA 5506-x within a specific subnet of our network, to isolate 3 devices, not the traditional firewalled, routed, internet access config in most examples I can find o...
Resolved! ASA5555-FPWR-K9 vs ASA5555-K9
Hello together,can someone explain, what is the effective difference between the following models in hardware and licensing? ASA5555-K9 - ASA 5555-X with SW, 8GE Data, 1GE Mgmt, AC, 3DES/AES ASA5555-FPWR-K9 - ASA 5555-X with FirePOWER Services, 8GE d...
Hi All, Is there an equivalent of the "show processes cpu-usage" command if I am running contexts? The command does not work on any of the contexts I have. Actually I can see the cpu usage is 90% and above ,I want to understand which process it is...
Can anyone please confirm my thinking for the CVE-2018-15454 SIP DOS Attack mitigation. If we only initiate SIP connections outbound and we do not have any rules allowing inbound connections, this attack is not possible from outside. I just want to...
Resolved! Tacacs / FirePOWER module
Is it possible to configure the actual FirePOWER software on an SSD for TACACs AAA or can local credentials only be configured / used for access?
Resolved! exporting rules
Is there a way to export the rules off the IPS so the actual rules can exported? I am using a 4240 6.x IPS and through the GUI I am able to export a "summary" of the rules, but not the actual rules themselves.Is there a way to do this through the CL...
| User | Count |
|---|---|
| 10 | |
| 7 | |
| 5 | |
| 2 | |
| 1 |
