I have two ASA firewalls in an active-passive standby arrangement. The secondary unit had a hardware failure and needs to be replaced. When I configure the replacement, do I need to put the ENTIRE running configuration on it and set it to "failover...
HI, i have an ASA firewall with local subnet 10.200.240.0/24 ASA interface is 10.200.240.10 There is a VPN tunnel between 10.253.0.0/24(remote) and 10.252.98.192/26(local nat) terminated at the ASA. 1-to-1 static NAT is configured between 10.25...
Dear Support, Can't able to access the FMC 1000 through web GUI, https://192.168.45.2, getting error " Unable to authorize access if you continue to have difficulty accessing the device, please contact the system administrator" But through SSH/V...
Hello Cisco Forum,
Can someone send an good command line example for setting up Sftp external to internal for ASA 5525? Also how to troutroubleshoot if its not working?
HI Guys. I,m new with source fire I end reinstalling the sourcefire module soft becuase a ASA replacement on the active. I got the stanby ASA with source fire module running. The previous network eng do not document the procedure, where can I found t...
I assigned FQDN to block youtube site with domain name google.com and nameserves 8.8.8.8 So the youtube site is blocked Ok, but i can,t browse any sub site of google.com, like google translate. So i ask you please for help.
I have configured the ASA with 3 interfaces (inside, outside and dmz). Inside and dmz get their IP via DHCP and they’re of course on different subnets. Outside gets its IP from the ISP (PPPoE) Everythings is working fine except for the DMZ interfac...
Hi All, I have an ASA5525-X (version 9.7.1) with firepower module (version 6.2). I added the ASA to the firesight management center, but I cannot see the interfaces of ASA listed in the Firesight Management Center.Please let me know whether anyone h...
Hi All, I need some advice with software selection for an ASA hardware upgrade. I have a customer that has an ASA 5512 that is running version 9.2(4)33 and I need to upgrade them to an ASA 5516-X, however this firewall does support ASA 9.2, and I...
Dears, My xlate are growing very faster I have plenty of IP address are doing lots of PAT and there are lots NAT commands with flags sIT idle 1157:53:39 timeout 0:00:00 TCP PAT from INSIDE:192.168.30.72/52890 to Internet:192.168.159.1/52890 flags...
Hi Friends, I will implement the follow topology, I have the follow doubts, can you help me? 1-) What model of ASA do you recommend to running firepower , with URL filter and Antimalware to Internet access, and IPS and Antimalware beetween all su...
I was hoping someone could shed some light on running Firepower right on the ASA vs running on a VM. We just got two ASA5515-FPWR-K9 units that we want to run in a Active-Passive pair. They have Firepower module version 5.4.0-764 and ASA version 9....
We will be deploying an ASA 5512 + Firepower in an isolated network. We will need to download update files and transfer to the ASA via CD/DVD. I see that the following updates are available for download from the Cisco site: VDB, Rules Updates and Geo...
Hello, I am planning to replace 2 microtick routers with an ASA 5508-X. I have different subnets in my lan 172.16.10.0/24, 172.16.20.0/24 up to 172.16.60.0/24. Also I have a range of public IP from ISP with x.x.x.x/28. I want each sub net to get out ...
