I have a SG52P 52-Port Switch with three VLAN's. Each VLAN has devices on a separate subnet (192.168.20.2, 192.168.50.2, 192.168.70.2) I have had no luck being able to communicate between the three devices although I have followed instructions on sw...
Forum Posts
I have an issue where if I use the Cisco ASA as the gateway I can't get to one of my Vlans. From within the Cisco ASA I can ping the IP and traceroute it but when I open a web browser it will not go. The only thing that works is changing the defaul...
Hi all,I've tried to make a redirect list to some traffic from ASA to Websense. This is part of the configuration:......wccp 0 redirect-list REDIRECT_WCCP group-list WEBSENSEwccp 70 redirect-list REDIRECT_WCCP group-list WEBSENSEwccp interface inside...
I just activated multicast routing on a blank ASA and it warns with this message:WARNING: Interfaces part of explicit zone will not participate in multicast-routing Could somebody clarify why it appears and what cisco means with explicit zone? Thanks...
The below does not work. Can't even ping the public address (.196). But if I change the test to make the source of the internal IP of the PBX an IP on vlan 1 (192.168.7.x) which is not sub-interfaced, I have no problems. Is this a 5506 bug or am I ...
I deployed an ASAv in Azure to start vetting it as a solution for the edge of out cloud deployment. According to every doc I can find on it, the ASDM should be installed and working. However, I've turned it on in he config and when that didn't work...
Hi, I am running a ASA 5525-X with Firepower, the firepower is managed from Firepower Management Center. Due to a bug in the current version I want to upgrade the module and the management center to the latest version. Can anyone tell me the correct ...
hello everybody, I have a issue with access the server (use port 80) with the ip 192.168.0.6 after upgrade firewall 5545 to version 9.8.2.28 before was 9.4(1). The problem is the following:I lose communication to the server every 3 weeks and I onl...
Hi Experts, I would like your help regarding my issue on my Active/Standby configuration on my ASA. Here is my topology and configuration below to better understand: ACTIVE ASA CONFIG failover lan unit primaryfailover lan interface FAILOVER...
Hi, I have the following NAT rule for an internal server to reach an SMTP server: nat (inside,outside) dynamic interface If I change the above to the nat rule below, email is not sent: nat (inside,outside) static interface service tcp smtp smtp ...
Hi,Last 2 day, network cable between ASA and SW faulty, thus we have changed it.but after that , weird think is email not able to send/receive and unable to open google.com, gmail.comthe user using smtp.gmail.com & pop.gmail.com other URL website abl...
Hello experts , I am getting a bit confused with the smart licensing feature. Not sure if i need it or not in my setup. We are buying 2 x 4120 + 1 x FMC. Required features : URL filtering , NGIPS , Anti Malware and firewalling. Can someone pl...
I have a ASA 5505 and ASA 5508x. In reference to the attached diagram. I am looking to fail-over a Public IP B to ASA 5508x through ASA5505. The only reason for this configuration is the ASA5505 is with ISP A and with out paying a huge amount we can ...
Hi All, I have a fresh ASA 5520 with a blank config that I am consoled into. It has a blank SSM-10 card installed. I am trying to configure the IPS, but every time I do session 1 from the console cable plugged into the ASA, it says "card in slot 1 d...
FMC by default provide multiple Access Control and Intrusion Prevention policies. Is there a way to view the content of the system provided access control policies?
