We are running two Firepower 1140s managed by a FMCv. Both are running 7.2.7. We have the AMP for networks subscription. When I search in my Malware/File policy to scan for .hta files I cannot find that extension. Has anyone else been successful in s...
Forum Posts
Resolved! FMC Migration from VMware to Hyper-V
Hello together, I am faced with the challenge that our customer wants to migrate his FMC installation from VMware to Hyper-V because he has switched his entire server infrastructure to Hyper-V. Unfortunately, there is currently no documented and supp...
Hello Everyone,We have a strange issue after 2 or 4 months, we are not able to reach the firewall and all the servers/systems connected with the firewall are not reachable.Then we have to hard reboot the firewall and after reboot it start working fin...
Hello everyone, I'm having a problem with my FPR 1000 series firewall, it was working before a long blackout happens, now when the electricity got up the firewall is acting up like this. Both of the port eth1 and eth2 are blinking at the same time a...
Hi, I made the mistake of clicking break HA which has disabled all the interfaces on my standby unit and disabled HA completely, I can no longer access it other than via the console which you cant see to do a great deal with. Is there anyway to recov...
Hello Team,Need help to create first ACL and NAT for our LAB testing . I have connected my subinterface with internet using PPPoE - I wanted to create ACL and NAT to allow everyone from internet to connect to the RDP on my inside host through my Subi...
Is it alright to put the IPS on both incoming and outgoing interface?i knew that we should put IPS on the incoming interface of gateway to protect our lan.But what if i want to prevent outside network from the attack perform by my asset in case of co...
Hi, We have configured 2 Firepower 8350 (v5.4.0.7) with the same health policy, system policy, etc. In one of these if we go to "Connections events" we can se the events recevided, but not in the another one (its empty) On the another hand, we woul...
Resolved! is this flow impossible?
hi I want to connect to M1/1 through inside2 and inside. how can i make it? thank you best regards
Resolved! HA FTD 2110 SNMP
I have two FTD 2110 version 7.0.4 configured with HA. I have configured a policy in Devices>Platform settings targeting the HA pair, in order to poll snmp from their Management interface. But during the discovery of the Secondary/Standby device its n...
Hi I have been given a task to Install PKI Root / Issuing CA Cert Objects onto a new HA FMCv deployment. I have setup HA and preconfigured everything. I have been provided three certs one root and two .pfx files from the customer. labelled root.p7bfm...
Hello there, we have recently upgraded to Snort3 and have enabled portscan detection. I wanted to check what are the recommendations for whitelisting to reduce noise (considering the whitelisting options are very basic). Also how do you guys manage t...
Hello all,I hope all is well.I am working on a project in which I am configuring an ASA 5508-X firewall. I just wanted to gauge what peoples opinions on what is best practice.In terms of the outside interface on the firewall should I configure it wit...
Resolved! ASDM unable to login for v7.18(1)152
Brand new ASA, I had connected via ASDM. No updates to the ASA, though not aware of anything on the client side changing either. ASA is v9.18(2) with ASDM v7.18(1)152. On one desktop I had tried various versions of Java from 1.8 202 to now 1.8 411 an...
Hello, I have received an RMA for a failed ASA 5508, which was the primary unit in a multicontext configuration with SFR modules installed. Could you please provide the correct procedure for reinstalling this device in production? Additionally, if ...
