Hi,I'm currently trying to implement redundant ASA architecture with failover technology, on packet tracer version 7.3.The problem is that i can't run the failover command on the ASA 5506 because the command is not found.When i do "show version" i ca...
I'm monitoring our Cisco ASA via SNMP.So far I found :- Total number of RAS sessions : 1.3.6.1.4.1.9.9.392.1.3.1.0- Number of IPSec VPN tunnels : 1.3.6.1.4.1.9.9.171.1.3.1.1.0- Total number of SSL Sessions : 1.3.6.1.4.1.3076.2.1.2.26.1.2.0I'm looking...
Hi All, I have BT broadband, I connected ASA 5525 and using PPPoE. The broadband itself is 400MB but the firewall interface that connects to BT is showing only 100MB. Its set to auto negotiation. ciscoasa# sh int GigabitEthernet0/0Interface GigabitEt...
hi,i need to migrate G0/0 "outside" and G0/1.xx "inside" sub-interfaces to a new port-channel1 interface.can't seem to pre-configure the same sub-interface VLAN and ip address under the same context.can someone advise what is the best approach and wi...
Subject: How do I perform a basic setup of Cisco ASA 5516-X firewall?Good day from Singapore,I have just bought a refurbished Cisco ASA 5516-X firewall on 17 March 2024 Sunday.How do I perform a basic configuration of this firewall?Any good guides to...
Hello Guy, Do anyone know how to check the existing the config-register on the ASA firewall please.when one of my HA firewalls reboots it goes to ROMON mode and I have to manually do boot to boot it up.How can i solve this issue please?I'm using ASA ...
Hi guys, When I SSH into my home test server I see the following error on Putty: "The first key-exchange algorithm supported by the server is diffie-hellman-group1-sha1". As SHA1 is no longer secure, I'd like to switch to something more secure. ...
Hello,I am getting an error with a printer authenticating with Cisco ISE for dot1x.The error is "Subject not found in the applicable identity store(s)".This is an LDAP identity lookup. It is looking for the alternative subject name DNS, and this is a...
Hi Everyone,we have N5K-C5596UP model and we would like to implement a brouteforce protection.The protection probably should work by timing out more then ... failed attempted logins on SSH and RDP.Let me know kindly how to implement this and thank yo...
I have 2 x FTD2110 managed by an FMCv, all v6.2.2. I'm trying to create an HA pair using an EtherChannel rather than a single physical link. However, only the physical interfaces are appearing in the dialog box to create the HA pair. The documentatio...
Hi All Have just come across an odd problem. Need to remove couple of lines from an existing ACL, however, there seem to be a limitation of some sort as there's no option to specify the ACL name, this is ASA 9.12 (same on 9.14, 9.16):(config)# no acc...
Hello I want to setup my cisco asa before my main router. I like to filtrate incoming ports. I like to enable transparent mode and configure as transparent firewall(I know all limitations of it) i set up all things but What IP i must add to bvi bridg...
Hi everyone. How to configure Windows NSP on Firepower as a radius server for authorization and authentication of VPN users. I will be glad if someone shares his experience.
Dear TeamWe have firewall FPR1010E model and currently it is under 90 days evaluation license , now my question is what next after my 90 days license is expired ?Waiting for your reply... Thanks & RegardsDhaval
Got a weird issue with some of my FTDs, running 7.2.5 on FMC and FTD. It seems if there is a new LSP update (we're on snort 3), 9 times out of 10, a policy deployment fails to remote FTDs. Without an LSP update, it works fine. With an LSP update, its...
| User | Count |
|---|---|
| 10 | |
| 7 | |
| 5 | |
| 2 | |
| 1 |
