Hi ,I want to upgrade OS version on following devices, Please advice the Downtime of OS up gradation. ASA 5550Current running:Cisco Adaptive Security Appliance Software Version 8.4(5) Requirements:Cisco Adaptive Security Appliance Software Version 9...
I'm about to implement my first 5520's, and I have questions about the details which aren't really explained in the documentation. My situation is active/standby.Failover Link:1. Etherchannel is now possible on the ASA's, but is it supported on the ...
We are using a Cisco 5585 to do one to one NAT and have noticed that we are close to the total number of available IP addresses. Is there a way to use PAT as a fail safe if the NAT pool is exhausted? Thank you.
Hi, Is there anyway to limit the bandwidth on module firepower on ASA5506, using ASDM to configure? Tks
Hi Guys, Can you please help me with configuring a asa 5505 8.2(5) with a range of ports.I have set ACL - access-list firewall extended permit tcp host 1.1.1.1 host 2.2.2.2 range 4800 4900what is the easiest way to add the static (inside,outside) fo...
I'm having some trouble sorting out an issue. It seems to be a pretty straight forward overlapping subnet issue but I can't seem to get it to work properly. At site A I have the 10.0.0.0/24 network. This network needs to be able to communicate with s...
Hi,I am facing the issue, where the SNMP query is not working properly for the below scenario, OpManager --> ASA FirePower --> 2911 Router The device is adding but only i can see the availability and response time. But i am not able to see the other ...
I've got an ASA 5505 firewall, which works fine most of the time. However, sometimes when I save the config to flash the ASA will freeze (amber light & all lights flashing on the ports). I've read on the internet that this symptom is due to faulty RA...
I know you can use a PAT pool and Round Robin for a one to many PAT (one inside address to many outside addresses). But can i do it incoming?I need to be able to NAT from a single public IP to a couple of internal IPs, each new connection going to th...
Hello community!I was reading the following article: ASA URL filtering without a Websense and I have additional questions regarding that process.Is my understanding that the website denied is denied globally thanks to the command service-policy globa...
In the document: FireSIGHT System User Guide Version 5.4.1 under section: Controlling Traffic Based on UsersWhat is being referred to as series 2 or x-series??? Is this a Firesight S/W version or:1) Series 2 = ASA5585-SSP-SFR-5,10 (Firepower modul...
I got an alarm while I remove a cable from my CISCO ASA (2 NE in HA).I don't see any alarm while I manually switch from active to standby.Is it a default/standard behavior ? Should I configure something to get an alarm ? Thanks, Benoît.
I currently have a Cisco ASA 5505 setup with a Site to Site VPN to a remote branch and the tunnels are live and working fine currently.I can access machines on the other branch subnet as well as ping anything on it but I cannot tcp/80 (HTTP) into any...
New to the Virtual Defense Center and ASA Policies/Rules. Looking for tips and best practices on the setup of policies and rules in my Virtual Defense Center. Not seeing very much traffic as far as Malware and File Events, which could be a really goo...
Hi As we know, failover has special ip address to connect primary asa and second asa. For example 1.1.1.1 and 1.1.1.2. Do you think that other device or other failover asa can use the 1.1.1.1 and 1.1.1.2 in the local network ? Thank you.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 06-05-2026 10:49 AM | ||
| 05-26-2026 07:54 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM |
