Hi Everyone, I upgraded ASA 5505 to Security plus license.i bought lic from ebay.Here is part of ebay that shows after upgrade it should look like this Output of show version after the upgrade:Maximum Physical Interfaces : 8 perpe...
Hello All Guru'sToday i came with some scenario in which i am having little bit hard time to understand again. Problem is i have a network in which we are running VPN between two Cities Datacenters. Both using 3 Vlans, like:In Chicago10.12.10.x, 10.1...
Hi Everyone, I have identity NAT config like belowstatic(inside,outside) 10.0.0.0 10.0.0.0 netmask 255.0.0.0when i do sh nat how can i check hit counts for above rule?ASA version is 8.2 RegardsMahesh
Is there any tool that can be used to document the ASA access rules to an excel or xml file?The documentation should include source/destination ip addresses, services and action.
My device has 3 interfaces configured: inside, outside, DMZ. Right now I can access the Mail server from the Internet using domain name which is on DMZ interface. The issue here is when users they need to configure their Ms Outlook for Incoming mai...
Hi allNeed some help regarding ACL configuration.Let's say I have an ASA with 4 interfaces (A, B, C and outside. Security levels for A,B,C are equal, outside is less)All clients on networks A,B,C are allowed to connect to outside. In this case I don'...
Hi Everyone, For one of our customer remote sites i need to open some specific ports between the servers.For this i need to config the ACL on firewalls.Say Source is 192.168.50.x Source is 172.16.10.x Source is 172.30.50.xDestination is...
Hopefully there are some ASA experts out there! I have been having an issue getting internet access working on VLANs and am literally tearing my hair out!Ok, just a quick summary of my environment. We have a 3750X cisco switch trunked over to an ASA ...
Looking for direction on where to isolate why the source (a.a.a.a) is not able to establish http connection with dst. I see these entries in the logs on the ASA.Apr 24 2014 18:12:10: %ASA-4-106023: Deny tcp src AHMCORP:a.a.a.a/47991 dst inside:172.16...
Hi, Is there a way to access the asa in a failover pair that is in standby mode from the primary asa?IE I am logged into the primary asa via command line and was hoping to access the other asa from here.Thank you.
I have a ASA 5510 which was upgraded to version asa824-k8.bin from asa723-k8.bin and after reboot it has reverted to the old versionThis may be because of Bootvar was not set ? but if wanted to reload it back to most recent version I am just wonderi...
I'm trying to figure out how to do a basic setup of our new ASA 5515x in a manner that will allow clients on the inside to access the internet.I know the topic has been covered before in many post here, but I've read them all (all I could find anyway...
I have a customer who wants to upgraded the ASA to 8.4.7(15) they are currently running 8.2.5(41), The customer wants to run the 8.4.7(15) code for a few days before rebooting the 8.2.5(41) ASA to get the upgrade, has anybody had any issues with r...
Greetings,I have a client who is replacing a single firewall with dual HA firewalls (in different locations) connected by fibre.The current connection is a single copper connection, using static routes. Q: Is there a way to utilise the single ASA551...
I'm planning to upgrade our ASA5540 active/failover pair from rel 7.2(4) to rel 8.2.(5) via rel 8.0(2).Would there be any issues with that or is it a simple upgrade?Is the 7.2(4) configuration sintax fully compatible with rel. 8.x, or there are state...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-05-2026 09:59 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM | ||
| 04-22-2026 11:56 AM |
| User | Count |
|---|---|
| 9 | |
| 2 | |
| 2 | |
| 1 | |
| 1 |
