Is there any plan to support ASDM on Windows server 2016 OS?
Is there any plan to support ASDM on Windows server 2016 OS?
We just changed a Module SM-56 on a Chassis 9300. Everything works great, only that now on the FMC the Device has now an IP instead of FQDN under management. All other Modules, and Devices are using FQDN for the Management Address, and it was working...
Hi Experts,I hope everyone is doing fine and well. I have this problem with my FTD for more than a month already. I will start this out with what happened at first.I have a ASA5508X hardware running on FTD7.0.6 with FMC 7.3.1.End of September we inst...
Hi dears,when entered the switch to universal P L R from F D M (Firepower Device Manager) , and copy the request code to smart license reservation, appears error as shown the attached image. how to enable !!
Good Morning all, I am working on a new network deployment and at the top is a Cisco Firepower 1120. I am going down to two datacore switches from the firepower and would like each datacore switch to have it's own uplink from the Firepower. Each in...
Hi everone ASA5510 can't connect ASDM and http port 443 and i know ASA 5510 EOL I use command "show run all ssl" command show "ssl encryption rc4-md5 des-sha1 3des-sha1"how to reslove problam? thankyou
HelloI have been trying to access my FPR 2100 firewall for around a week but without success.Before the problem occurred I freely connected to the port management and typed the address 192.168.45.45 in the browser to access the device manager web int...
Hello,I am currently configuring two Cisco ASA 1120s for Active/Standby failover. So far it is failing. This is what I have done so far. The version that these ASAs are running is Cisco Adaptive Security Appliance Software Version 9.16(4)42. They als...
Hello Team,Is it possible to filter VPN remote access with mac-addresses as a second layer factor security in addition to username/password on FMC?If yes, any ideas to approach this?Thanks.
We are having a Faulty SM-56 (in a Firepower 9300)slot/1/fault/F1546Description:Security Module 1 is in failed state. Error: Security module is downgraded (or) not acknowledged. Reason: DIMM or CPU degradedWe even know which DIMM is bad: Memory Array...
Hello, I have built an IPSEC site to site VPN tunnel from one of our Cisco ASA to Fortigate firewall. The tunnel is up and running and traffic is passing though the tunnel as expected. Now I have a requirement to track the tunnel status via SLA monit...
I'm working on setting up a pair of FTDs to replace existing ASAs. FTDs and FMC are running 7.2.5. The ASAs have the following timers configured for OSPF: router ospf 1 timers pacing flood 5 timers pacing retransmission 60 timers throttle spf 10 1...
Hey everyone! I have a weird situation going on with my failover and I just wanted to make sure the best practice for the HA Pair of a FTD. I have two outside interfaces with the same IP and I think when they have the same IP it broke the HA pair. Q...
Firepower 1010 (ASA-Image): ASDM does not work anymore after upgrade Hello everybody, I upgraded the Firepower 1010 (ASA-Image) from 9.14(4) auf 9.18(3)56using the ASDM and the upgrade worked without issues. Directly after the upgrade I still could o...
Hi,We used the migration tool to move from ASA5525s to FPR3110s and the tool appended "no-lookup" to most of the rules but not all. If anyone knows what this designation implies, as well as it's absence, I would greatly appreciate knowing. Thanks.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-16-2025 04:21 AM | ||
07-06-2025 01:40 PM | ||
07-04-2025 01:59 AM | ||
06-19-2025 07:32 AM | ||
06-17-2025 01:07 PM |
User | Count |
---|---|
10 | |
7 | |
5 | |
2 | |
1 |