Hi,I've received two Cisco ASA 5505 and am unable to connect to the ASDM website on either. Ive done all the basics and but something is clearly wrong somewhere considering its happening on both.With the default settings on the ASA I am able to ping ...
Hi All,i have configured the Netflow to 172.16.0.y server and i am getting all the netflow traffic.but i am not getting any syslog message to my other syslog server(172.16.0.x).Regards,Prashant
I have a 5510 and am going to install the AIP10SP-K9 SSM module and am wondering what the gigabit port that comes on this is used for? Is it just for remote management? thanks.
I know this topic has been covered may times, but I am still stuck after reading many forum posts and cisco help files on the subject. Also let me say that I am not a Cisco professional in any way, although I do know my way around the CL to some exte...
hi,have an below subinterface,interface GigabitEthernet0/2.50description *** Connected to DMZ **** vlan 50 nameif DMZ security-level 50 ip address x.x.x.x/27need to allow this subinterface accessible through out network
I have two 6513-E switches that I have enabled VSS on to make one logical switch.These switches have ASA service modules in slot 9, and they show up when I do a "show mod"When I try to get into the module by issuing the commandsession switch 1 slot 9...
Dear All,I am trying to connect my switch 4510 to my ASA5510. But line protocol on my switch showing down.Sub interfaces are configured on my ASA and the switch port conneting to firewall is configured as trunk.L2 Vlan also created in the switchAsa v...
The FTP server log shows no hits, from 192.168.1.4 I can telnet to 5505 no problem.Doing everything on inside interface eth0/1, ftp server shows up and arp table of 5505 has correct mac for 192.168.1.4ciscoasa# copy ftp://[email protected]/asa841-k8.b...
Hi,Not sure if this is in the right section but hopefully it is.I need some clarification on the licenses required for phone proxy to work. Is it just the 'UC Phone Proxy Sessions' license? or do i need the 'AnyConnect for Cisco VPN Phone' license as...
Does anyone know if it is possible to force the NAC agent to load up first on boot-up in a windows 7 OS ? I'm aware that delay's can be implemented but the client does not want to use login scripts.
Hi Everyone,Found this about troubeshooting ASA connections--ciscoasa# show perfmon PERFMON STATS: Current Average Xlates 0/s 0/s Connections 2236/s 321/s TCP Conns 2236/s 321/s UDP Conns 0/s 0/s URL Access 0/s 0/s URL Server Req ...
I have a customer with a ASA5520 with a CSC module. Unable to log into the CSC gui directly or via the Link within the ASDM.We removed the card and installed it into his spare ASA and show the same issue. We put the spare card in t...
Hi,I am having trouble with our ASA5510.After upgrading the internal memory from 256 MB to 1 GB and upgrading the firmware to 8.4.2 we are experiencing that the ASA is running out of 1550 byte blocks. When that happens it is not possible to connect t...
HelloHow do I configure dhcprelay over a IPSec VPN. The endpoint is a ASA 5505 that will use dhcprelay as a backup to the local dhcpserver. How must the crypto ACL be designed to match the packet? Will it match on 0.0.0.0 or the outside IP of the fir...
Hello,ASA Firewall is running in Active/Active mode. Below is the configuration of the firewall and IPS SSM module.We are not getting event on IPS sensor when we type "show event alerts".IPS configuration:++++++++++++++++++++++IPS1#IPS1# sh configura...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 11-10-2026 12:34 PM | ||
| 11-06-2026 12:20 AM | ||
| 09-22-2026 04:13 PM | ||
| 08-25-2026 06:22 PM | ||
| 08-24-2026 12:26 AM |
| User | Count |
|---|---|
| 2 | |
| 1 | |
| 1 | |
| 1 | |
| 1 |
