xx
xx
I currently having ASA 5505 setup and my ISP is comcast and my current setup is Comcast-ISP modem --> ASA5505(FW/DHCP) --> Netgear WNDR3700-Wireless--> clientsI'm planning to switch over to Verizon Fios (internet only) soon, i was reading that Fios ...
HI Experts, In my company PCI audit is happening & they found below two issue. what necessarie changes should I done for this.
There is one config that I can not figure out how to translate it over...ip nat inside source static 10.4.200.29 27.166.58.194ip nat inside source static 10.4.200.25 27.166.58.195How do I do this on the ASA 8.2.5? (came from a 2800 router running ver...
Dear all,I need to configure zone-baesd IOS f/w on 1721 router.I have loaded c1700-entbase-mz.124-15.T9.bin .But commands are not accepted.Could any body tell me what is the correct software I should download (adn it should be av...
Greetings all and thanks in advance for any assistance.I have two PIX 501's that I wqould like to reset to factory defaults but don't know the logins. Trying to get into them via telnet and the connection is refused every time. Not CISCO savvy by any...
Hi,I'm trying to get NAT64 to work on an ASA. I've read the release notes for version 9.1 but the examples in them don't seem very helpful as they deal with access to indvidual servers.I'd like to set up what I think must be the most typical case:Ins...
Hello,I have a question about the ASA and the ARP traffic in IOS 9.1.2 for ASA 5585-X and multicontext. I have discovered a curious behaviour about the traffic ARP in the my CLUSTER of ASA's. When I try to send a ping between host in the same subnet...
Hi,We are Having ASA 5525 firewall and Whenever I am performing traceroute passing through the firewall and i am not getting any hop count after firewall( Firewall IP is also not shwoing in Trace Route.ICMP I had allowed and also configure ICMP in t...
Dear Sir,We are unable to configure MS outlook in our network which is having IWSVA proxy and cisco ASA 5510 firewall.snapshot of outlook error details are attached for your reference. In our network L3 is behind IWSVA which is behind cisco ASA 5510...
hi,i have a cisco 5500 ASA running on 1024 bit certificate. Now i need to update to 2048. how do i go about doing this ? do i remove the exisiting certificate and then add the new one or can i simply update with the exisiting one ?if anyone has a lin...
Hi all, I have an ASA 5510 8.4 that has an IPsec tunnel with a non Cisco device. I have a domain controller on each side of the tunnel (part of the same windows domain) It seems Active Directory is not replicating through the tunnel. What are the ste...
I have pulled my ASA5505 out of my internal network, after hearing that ASA needs direct WAN ip access to have VPN running. (at least for novice/freshmen like new CCNAs like me).ASA5505 has direct WAN mapping now and has a non-private IP address.I'm ...
Hi,We have two ASA 5510s in separate locations, connected across the internet.We have a site-to-site VPN between each of the ASAs that enables a SAN device at each end to replicate data to the other.The replication, when running, will consume all ava...
Here is a scenario I'd like to know about:A Cisco ASA running 8.2.5 with 3 interfaces: Outside (Sec lvl 0)/-nternet IP / DMZ (Sec lvl 2)-192.168.8.0/24 / Inside (Sec level 100)-192.168.1.0/24An ACL on the DMZ which looks like this:access list DMZ_IN ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 08-25-2026 06:22 PM | ||
| 08-24-2026 12:26 AM | ||
| 08-20-2026 05:54 AM | ||
| 08-19-2026 07:59 AM | ||
| 08-10-2026 08:58 AM |
| User | Count |
|---|---|
| 4 | |
| 1 | |
| 1 | |
| 1 | |
| 1 |