Say I have a FMCv (running in VMware) managing about 20 FTD firewalls (1k and 2k models) currently. I want to plan to move my existing FMCv to cdFMC within CDO. Is there a way to migrate the existing FMC configuration, such as the policies and object...
Forum Posts
There was an issue with uploading the new image to the backup FMC. To find out why I want to access the FMC via cli and find the password wrong. So, I have checked the document to reset the password. After rebooting the host with single mode, try to ...
We have a number of FPR2110-NGFW-K9 in different zones in a network. They are standalone and not managed by any controller (one fw in each zone, data-diodes between zones).The fw's are sending syslog to our loggserver but there isn't any host informa...
Hi all,Customer has two 1120's running in single mode and in active/standby failover configurationnow i would need to put them into multi context modei tried first to put the active into multi context mode (via console)it starts as expected:pri/act/a...
Hi everyone,I have some questions about ports and communication serial.1.- What does it mean "Segmentable network port"?2.- What standards about Network Security apply on "Serial Port"?My technical Specification of my device are:I really appreciate y...
Resolved! IPSEC TUNNEL MONITORING- ON FMC
Hello,I have two ftds in HA being managed by fmc on vmware. is there a way for me to monitor these ipsec tunnels, and get alerts if any tunnel goes down?Ideas on tools that can do this, and how to integrate the same.your support will be much apprecia...
Hi, is there any config conversion tool for concerting Firewall config from traditional ASA 5510 box to firepower 2110 ASA appliance. Both boxes are running on 9.x ASA code
Hi all,I have Cisco switch CBS350 (I hate this switch because of different CLI commands).I need to delete switchport configuration (like this: "default interface fa0/0"), but "default" command not works. I couldn't find specific command for it. Can y...
Hi there I have a new firepower 1010 and for some reason I have the error message “gateway cannot be reached through port Ethernet 1/1 named outside” I know my isp line is up and running and NAT rule is on dynamic and yet I still have no internet on ...
Hi there,got a new firepower 1010 and stuck at first hurdle setting it up .. at first boot I put in manually my Static IP, subnet and GW and it won’t connect out .. I’ve put these IPs into my laptop and works so I know my external line works .. but a...
Im new to firewalling and im currently trying to allow traffic from Office 365 on our Cisco ASA 5515-X Is the a way to use FQDN with wildcard (ex. *.office365.com) There are numerous destinations similar to the example to allow Office365.
思科型号ASA5555-X的show version和dir查看flash的命令，可以看到当前Cisco Adaptive Security Appliance Software Version 9.12(4)29 也就当前的思科自适应安全设备运行软件的版本是9.12(4)29的文件为asa9-12-4-29-smp-k8.bin，，还是供客户端安装的自适应安全设备管理软件的版本为 7.13(1)，通过dir可以查看到当前文件名为asdm-7131-101.bin大佬们可以帮确定下这个原来老...
Hello.i'm trying to setup some subinterfaces the following wayInterface GigabitEthernet1/7.2Vlan 2192.168.2.1Interface GigabitEthernet 1/8.2Vlan 2192.168.2.1how ever it doesn't allow me to put vlan 2 on the 1/8.2 subinterface "ERROR: Vlan 2 exists in...
Hi,I've been searching for install procedures for Secure Client software on Firepower but not finding it. If someone could please share a procedure that would be great. Is it like installing AnyConnect on ASAs?Also have questions' about licenses: if ...
What is ASP in ASA?How it works.Router forward Traffic based on CEF.then How ASA Forward traffic?
