Just installed 7.1(2) and various ICMP ACL rules now have a Red Dot with the number 4 in them. Older version of ASDM (6.x) didn't display this. Before I start digging through logs I search the manual and didn't see any specific reference. "4" is sou...
Hi,Recently moved into the hardware firewall space and have a ASA 5510. Having some issues trying to get traffic through the box to my 4 dedicated servers. all the servers have static IP's and are connected to a private switch into one of the etherne...
Hi,I am trying to use Nat exemption for our publicly routeable IP space (for a web server in this case) so that people from the outside can connect to it using its actual IP and it seen as coming from its actual IP. Running sh xlate shows that the p...
We are setting up an old office building as an offsite data center. The network cosists on a PIX 501 firewall and a 2811 router. I am attempting to setup a GRE tunnel over IPsec back to the main office. The main office consists of a PIX515, a 2821 ...
No, I am not talking aout my knee....I have a 2621 router - old. but works well.Need to put in an ACL to limit the inbound SMTP traffic to be FROM a specific set of IP's, and deny all others.I have tried various combinations with no luck. Something ...
Hi.I am faced with a peculiar situation on my productin firewall. I would like to ask a question. Will cisco firewall allow the response coming from different MAC Address. I am not having any ACL w.r.t MAC.
Hi,We've been deploying an ISE solution (1.1.0-665 version) in one customer and we have one doubt regarding Posture Assessment/Remediation. We're trying to check AV installation and definitions and this check is working fine but things get a little b...
Hi,We are experiencing very intermittent issue with NATing. It happened twice now in two weeks. First time it lasted for about 10 minutes, second time I had to failover to satandby firewall. We have Cisco ASA 5510 with 4 IPSec VPN tunnels. Everything...
Hi guys.Can anyone point me in the right direction to setup ciscoworks/CSM to use AD authentication? Is this setup supported?We're currently running CSM 4.4.0.Thanks.
Hi there,I would like to ask if the ASA failover/ sync is still working when the primary ASA has a CSC-SSM-20, the secondary a CSC-SSM-10?The ASA's are the same type/memory.Thanks,BorbertSent from Cisco Technical Support iPhone App
Hi Everyone,I was trying Basic url filtering BY CBAC on routerusing CBAC (Context-Based Access Control) : ! ip inspect name WEBFILTER http urlfilter ip urlfilter allow-mode on ip urlfilter exclusive-domain deny .yahoo.com ! ! interface FastEthernet 0...
Do we have something similar to track list on IOS for my below Cisco ASA?I wanted something similar to this on ASAtrack 2 ip route 10.200.1.1 255.255.255.255 reachabilitydelay down 20 up 20track 3 ip route 10.200.1.2 255.255.255.255 reachabilitydelay...
Hello,I am running an OpenVPN server on an internal private network on port 1194/UDP and would like to open this port for the internet on a Cisco 1812 router (this router uses Zone based firewall). For that purpose I have added the following configur...
The attached jpeg shows my network. I want to be able to access the internet from all routers behind the ASA. How is that done?
Hi, I needed to block traffic between some VLANs by default in the same context of fwsm. Can I remove the permission that allows traffic between VLANs with the same level of security (same-security-traffic permit inter-interface) and put those VLANs ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 08-26-2026 04:36 AM | ||
| 08-25-2026 06:22 PM | ||
| 08-24-2026 12:26 AM | ||
| 08-20-2026 05:54 AM | ||
| 08-19-2026 07:59 AM |
| User | Count |
|---|---|
| 3 | |
| 2 | |
| 2 | |
| 1 | |
| 1 |
