Good Morning all, I am working on a new network deployment and at the top is a Cisco Firepower 1120. I am going down to two datacore switches from the firepower and would like each datacore switch to have it's own uplink from the Firepower. Each in...
Forum Posts
Hi everone ASA5510 can't connect ASDM and http port 443 and i know ASA 5510 EOL I use command "show run all ssl" command show "ssl encryption rc4-md5 des-sha1 3des-sha1"how to reslove problam? thankyou
HelloI have been trying to access my FPR 2100 firewall for around a week but without success.Before the problem occurred I freely connected to the port management and typed the address 192.168.45.45 in the browser to access the device manager web int...
Resolved! Cisco ASA1120 Active/Standby Failover
Hello,I am currently configuring two Cisco ASA 1120s for Active/Standby failover. So far it is failing. This is what I have done so far. The version that these ASAs are running is Cisco Adaptive Security Appliance Software Version 9.16(4)42. They als...
Hello Team,Is it possible to filter VPN remote access with mac-addresses as a second layer factor security in addition to username/password on FMC?If yes, any ideas to approach this?Thanks.
Resolved! FTD Module FPR9K-SM-56 Faulty DIMM / RAM
We are having a Faulty SM-56 (in a Firepower 9300)slot/1/fault/F1546Description:Security Module 1 is in failed state. Error: Security module is downgraded (or) not acknowledged. Reason: DIMM or CPU degradedWe even know which DIMM is bad: Memory Array...
Hello, I have built an IPSEC site to site VPN tunnel from one of our Cisco ASA to Fortigate firewall. The tunnel is up and running and traffic is passing though the tunnel as expected. Now I have a requirement to track the tunnel status via SLA monit...
Hey everyone! I have a weird situation going on with my failover and I just wanted to make sure the best practice for the HA Pair of a FTD. I have two outside interfaces with the same IP and I think when they have the same IP it broke the HA pair. Q...
Firepower 1010 (ASA-Image): ASDM does not work anymore after upgrade Hello everybody, I upgraded the Firepower 1010 (ASA-Image) from 9.14(4) auf 9.18(3)56using the ASDM and the upgrade worked without issues. Directly after the upgrade I still could o...
Hi,We used the migration tool to move from ASA5525s to FPR3110s and the tool appended "no-lookup" to most of the rules but not all. If anyone knows what this designation implies, as well as it's absence, I would greatly appreciate knowing. Thanks.
Hello folks, What are the best practices to fix local subnet (RFC 1918) URLs that get classified as uncategorized. Is there a better way than adding them to a URL list as a feed or as a URL group. The exercise being that I want to identify them a...
Hi all,I need some assistance with ALC'sSo my goal is to have an ACL that blocks access to the switches web gui BUT allows an ISE URL redirection for our guest users.In order for the redirect we need to have the http and http secure-server active,Thi...
Resolved! FMC protocol (n)
Hi. Can anyone tell me what the number in brackets in FMC policy editor means in the protocol drop down field? thanks
i have Cisco ASA5516-X Threat Defense with ios version (75) Version 6.2.3.17 (Build 30) and i intended to upgrade to 7.0.1 but i have to go 1st through 6.4.0 so i upgraded the ASA to isco ASA5516-X Threat Defense (75) Version 6.4.0 (Build 102) then t...
Hi All,I'm getting "packet 1420 bytes greater than effective mtu 1398" PFA, when trying to send an SMTP traffic via IPSEC VPN, Could someone please advice on this?Device: CISCO ASA 5525
