Hi allI'm having some trouble setting up an active ftp session from inside to outside.I've read the other topics on the forums, but i can't figure it out myself.I created some acl's and port forwards, i also configured the inspect FTP in the global p...
Simple question, but i did not find on the cisco docs... what is the version od SNMP that the IPS can work ? is it v1, v2 or v2c ?Thank you
On the IPS 4260-k9 under the cisco.com server settings the url is the default but there is a section that states Username and Password. I put my CCO id information in this location. And when I go to the url that is in there it brings me to a page tha...
Hello Guys,S.O.S....Right now, every one can go to ASA FW via browser (ip address specified on my outside interface) and connect, download certificates and AnyConnect client with assigned uname and password.What i am trying to do is:Configure my ...
I have my PIX 515 setup to sync time to one of the Naval clocks, and it seems to be working fine. I would like to have my Windows Active Directory server sync its time to the PIX what additional steps do I need to take?
Hi,One of my customer is having problem to login to the ASA at the privilege mode, He has access through ASDM. He has changed the enable password through ASDM but no luck. Here is the config:aaa authentication ssh console Radius LOCALaaa authenticat...
We have several partners in different countries who are using overlapping subnets on their switch hardware. we have to manage all the partners hardware from our netmanagers which are installed behind an ASA5510 firewall. We have a single port to the...
Hi,I have 2 problem in IPS-4255-K9. my network has 2 device of IPS-4255-K9 and each have different problemProblem no 1:My IPS-4255-K9 after running for 1 hour or less than that starts to hang and all the traffic is blocked as it is inline mode.Probl...
Hi,Reading through the documentation recommendations and I would like to configure the following setup http://www.cisco.com/en/US/docs/security/asa/asa83/asdm63/configuration_guide/ha_overview.html#wp1095702 scenario 4, figure 58-6 but I can't find s...
Hi,I have an ASA5510 with a couple of servers behind it, using NAT. The configuration of Ethernet0/0 is:(using fake IP's)!interface Ethernet0/0 nameif outside security-level 0 ip address 99.99.99.40 255.255.255.224!The IP-range I can use is 99.99.99....
I have to make several changes in the configuration due to our company switching Internet Service Providers. Is it best to do a "show run" at the command line, then just copy/paste new config into the ASA? Or is it better to run the "more system:ru...
Hi,I want to upgrade the IPS module in an ASA 5510 and have a few questions. The AIP-SSM is running 6.2(1)E3 479.0 and I have a valid CCO account etc for this.Does the Software version on the ASA matter?When I look in software downloads < IPS there a...
Hello,Sorry for the basic question, but does anyone know how many ACL's is supported on a ASA5550?I have a client that is looking to move 7.200 ACL's from a Cisco 2800 router to a Cisco ASA5550 and would like to understand the below:-How many ACL's i...
Hello -I am attempting to access a SSL terminating webserver on an internal host through a PIX 515 running 8.0.I have an inside and outside interfaces defined.I wish to have any external host use SSL to access the destination webserver.I also have a ...
ASA version 8.2I ran the IPsec wizard on my 5510 for remote access. It would seem that by default ISAKMP is enabled on both the inside and outside interfaces. Furthermore, my default dynamic crypto map is enabled on both the inside and outside inte...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-05-2026 09:59 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM | ||
| 04-22-2026 11:56 AM |
| User | Count |
|---|---|
| 6 | |
| 3 | |
| 1 | |
| 1 | |
| 1 |
