Hi,i installed last week CSM 4.0 and AUS 4.0 in a customer CED.I need to backup the ASA config (running or start-up) to AUS every day.Is possibile ?If yes can some on help me?Thanks a lot best regards.
Hi,i installed last week CSM 4.0 and AUS 4.0 in a customer CED.I need to backup the ASA config (running or start-up) to AUS every day.Is possibile ?If yes can some on help me?Thanks a lot best regards.
Hey,I'm configuring 802.1x multiple authenticatino with C3560G.Without any timer changes, user's mac address is registered by static on mac address table.The issue is that if authenticated user moves to non-802.1x port, this user can't access network...
I have a WS-SVC-IDSM-2 that I have been tasked to setup. Currently the focus is around our pair of ASA’s that are used for internet access but the scope could increase. I am getting some conflicting information on how to setup the packet capture to t...
Hi,Is it possible to port forward a range say from 3000-4000 using ASA?Do let me know how to do it.Reg,Sushil
I have a DMZ configured that should normally only allow traffic to http, mail, etc. However, I would like to allow admin traffic like ssh from certain IPs as well. For example, my DMZs are behind one IP range from one ISP. My LAN is behind another IP...
1. How can I see what software versoin the sensor is running.2. How can I manually update the sensors image. 3. How can I see through the cli when the signatures were last updated.4. How can I unblock traffic that is being blocked by the Sensor.
I am not able to get WCCP working on the ASA (with Websense). How does the ASA know the IP address of the websense box as I am unable to see it in the configuration?Below is what I have configured. My clients go out to the internet but are not redi...
i have FWSM added in CSM , after i discovered all the configuration on the fwsm , i tried to add an interface , the when deploying the change , the session hanged , i accessed the fwsm to see what is the problem , i found 6 vlan interfaces deleted b...
Hi,I am trying to setup two pairs of ASA 5510s which they will both be setup as Active/Standby. The failover interfaces will be connected via Ethernet to the same switch. Do the interfaces need to be on separate individual VLANs on the switch to work...
Kindly suggest whether the below NAT configuration can be done in FWSM.I have one Internal Interface & two external interface. The natted Global Address should be same for traffic routing via both the external interface.static (Internal,Outside1) 11...
Hi. I'm having issues trying to manage a Pix 501 remotely on one of our satellite sites. I can connect to it locally using ssh client (putty) and PDM but neither work from outside (Internet Explorer cannot display the webpage - via PDM). As far as ...
Hello,I use a cisco ASA firewall in a L3 configuration.Result of the command: "show running-config sysopt"no sysopt connection timewaitsysopt connection tcpmss 1380sysopt connection tcpmss minimum 0no sysopt nodnsalias inboundno sysopt nodnsalias out...
Hello,I have problem with communications through ASA to MS exchange server.I'm testing new connection to the internet and ASA is a default-gateway for my VLAN (user VLAN).It's a similar problem described in this doc 'http://www.cisco.com/en/US/partne...
I have a NAC Manager with two licenses OOB and now I put two more CAS HA OOB licenses butafter I put that licenses i saw that Active Manager added just CAS OOB and Standby Manager added without problem.take a look these pictures.thanks
Hi,Is it possible to know what "shared key" was used for NAC communication (CAS and CAM) in a setup that is currently in production?RegardsPrasanth Mathews
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-22-2025 09:48 AM | ||
07-16-2025 04:21 AM | ||
07-06-2025 01:40 PM | ||
07-04-2025 01:59 AM | ||
06-19-2025 07:32 AM |
User | Count |
---|---|
10 | |
5 | |
5 | |
3 | |
1 |