Which Cisco firewall can be pitched against Fortinet UTM box??
Which Cisco firewall can be pitched against Fortinet UTM box??
Where do you pull statistics on the ASA to determine my current teraffic patterns to a DMZ server so I can estimate reasonable values for connection limits?
I'm trying to add another static nat translation onto the ASA. There's already one static nat to another host. Wouldn't I just copy the same static and change the IP's? Tried it and it gave me a error. Not sure what else I'm suppose to add. Kinda los...
there a doc in cisco which speaks of configuration of backup links.question;sla monitor 123 type echo protocol ipIcmpEcho "IP address" interface outside num-packets 3 frequency 10 The ip address can be any ipaddres on the internet ?What happens if i ...
I have a remote site that I need to block some outbound Internet traffic. The site is setup as a PPPOE for Internet access via a DSL modem and they have a T1 connection to the corporate office. I have an ACL setup to take care of Inbound Internet t...
i have a IPS 4260, running Version 6.0(5)E2.I have noticed different duplex on the interface.My understanding based on the logs below:The interface below seems to be running in half duplex, but they are configured for full duplex.-GigabitEthernet2/0-...
Hi,I've Cisco Security Manager Suite with IPS Manager.I want to add a sensor...I go to Devices->Sensor as suggested by User Guide.But when I open the page i don't have the Add function, but only Re-Import and Reboot...Why?I've not powered on the sens...
Hi All,Please can someone provide me an advice on this?1. We are about upgrading our PIX 515E/ failover pair from 7.04 to 8.0x. but not sure which release has been tested and confirmed to be the most stable. I want to know which is the best version t...
Hello everyone,Is there a place on CCO where a list is provided of known viruses/worms that will be detected by the latest IPS signatures?Regards,Jesper
Dear All,When i am trying to access one server which is above my ASA i am getting the following error.=======================Dropping TCP packet from Outside:10.20.8.52/30000 to Inside:10.20.0.243/34538, reason: MSS exceeded, MSS 1380, data 1436=====...
Hi All, I have two ASA as active/standby failover. these two are connected to 3750 switch through trunk port that carry vlan 10,20 and 30. I want to deploy IPS in between with inline mode. I am little confuse how to connect IPS here. should it be con...
Hello, we are deploying Cisco 871 routers to our customers, we do a simple IPSEC point to point VPN connection. We want to ensure the VoIP traffic is granted over the data traffic.I did this config but I don't know if I'm doing it right, because I th...
Hi,I've a IDSM-2 module (installed on a Catalyst 6500).This module is PowerDown; when I issue the command "power enable module .." the module can't be on line. I see this message on logging: %C6KPWR-SP-4-DISABLED: power to module in slot .. set off...
Hi All, Can I use inline pair in IPS as trunk? The IPS is connected to ASA in one end and connected to switch to another end. I'd like to use inline pair but I am not sure if it can pass all vlan traffic. thanks Alex
Hi Everyone, I followed some sample configs online and configured my c1841 router to acceppt VPN Client connection. Now I'm able to connect the VPN Client to the router and able to ping the router's LAN IP address, but I couldn't get to any other com...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-16-2025 04:21 AM | ||
07-06-2025 01:40 PM | ||
07-04-2025 01:59 AM | ||
06-19-2025 07:32 AM | ||
06-17-2025 01:07 PM |
User | Count |
---|---|
11 | |
6 | |
4 | |
3 | |
1 |