Network Security

Hello, I am again having another problem with my NATTED ip. We have connected a server on one of the Firewall interface. I can Ping the server 10.26.34.20 from the Firewall context at the same time, I can ping the 10.10.10.10 server from the firewall...

Hi Guys,It is my first time to inquire on the Cisco NetPro Forums.I am currently having a problem with one of my set-up in our production environment. Let me first start by describing the set-up of the network infrastructure. I have a two context ...

Dear allI want to know what is the use of the below commands?static (dmz,inside) 10.1.200.165 10.1.120.20 netmask 255.255.255.255 0 0 static (outside,inside)10.1.201.64 195.216.21.7 netmask 255.255.255.255 0 0What is the difference if I we write them...

Hi,As per my understanding on NONAT satement in Firewall( up to IOS version6.3) is,,,,If any packet traverse from Higher secuity to lower security--permitted by default r by ACLIf any packet traverse from Lower secuity to Higher security need to be a...

Dear all, I need to convert routed mode to transparent mode on my ASA-5510 with inbuilt IPS.let me know which of the following features configured on my firewall will have issue if converted to transparent mode:1. static routes.2. object-groups.3. ...

I've just installed an evaluation copy of LMS3.1. I performed a discovery and wanted to take a look at the map.When I click any link for "Topology Services" I get a pop-up, which then imediatly closes.If I open up Campus Manager and go to the Visuali...

Twice in the past two weeks my ASA 5520s in an Active/Standby setup have failed over when it appears there should have been no reason to.I think this is is 3 or 4 times total they've done it since I implemented them. After the first false failover m...

Hello...I have a PIX Firewall 515E with version 8.0.2 and ASDM 6.0.2 and I have a problem.I enabled the Top Usage Status (Top 10 Services / Top 10 Sources / Top 10 Destinations) in the 'Firewall Dashboard' menu and now the Memory Utilization is very ...

I am trying to configure AnyConnect and I used ASDM to configure it the first time. My error is when AnyConnect tries to establish VPN it comes back with an error "No Assigned Address"I pointed the Policy Group to the IP Pool and everything appears ...

Dear Superb techies I need help to configure FWSM module Here I begunI have 2 6509 switches acts as datacentre switches and each have one fwsm module installed .I have 200 vlan on connected distribution switch - core via trunk and to datacentre users...

trying to troubleshoot a host that sits behind a configured interface on a FWSM running 3.1(7). There is an ACL applied to this interface and its filtering other traffic for this host I am troubleshooting and it shows hits on the acl's, however, I pu...

I'm using FWSM with software 3.2.4 and a TCP syslog server with permit-hostdown option.If I stop the server, FWSM continues to work. When server restarts after some minutes, the FWSM doesn't send any syslog messages to it.In order to re-establish con...

Recently, a few Windows XP clients have been experiencing a very annoying behavior. A whole raft of processes are showing up in the logs as '<Unknown: [pid]>' and user query responses about actions performed on or by these processes do not get assoc...

I woder if using ASA or PIX, can I set up the outside interface with 1 IP then for outgoing (on the same outside interface) with another IP address. For example: outside IP 1.2.3.4 then somehow for outgoing(return traffic if you will) the IP address ...