Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Hi I am Newbee to ASA configuration. recently we brought one ASA5505 i tried my level best to configure the ASA we are getiing PPPOE IP from ISP. after PC are not able to browse. from ASA i am able to ping the outside network. can any one please help...

rsjavahar by Level 3
  • 3042 Views
  • 14 replies
  • 0 Helpful votes

Hello,We have a PIX 506 firewall and I need to allow a specific IP address, 141.157.129.77 to access a server inside the LAN on port #1999. I created a public IP address for the server but I am not so sure if the following command is correct. access-...

h-kholghi by Community Member
  • 671 Views
  • 1 replies
  • 0 Helpful votes

I'm trying to create a mesh network using dmvpn, and everything works great until I put an ASA5520 in front of the hub router (2801). The ASA initially blocked all communication to the spokes, but after browsing the forms I found the following comman...

Hi,I have local digital voice server which is Siemens hi-path 3000.and from this local site i have configured IPSec Site-to-Site VPN to a remote site, ASA from my local side and Cisco 2811 with IOS firewall.Now, the remote IP phones is connected and ...

Can somebody please send me a known working snippet of ASA config to support a DMVPN hub NAT'd behind an ASA. I tried for 2 days even with TAC and I was finally forced to put my DMVPN Hub out on the Internet with the IOS FW.Basically the issue I was ...

patrickg by Level 2
  • 1199 Views
  • 2 replies
  • 0 Helpful votes

I have a requirement to NAT the destination address and destination protocol port on the ASA5550. The ASA appears to only NAT inside address to the outside. Is there a way to NAT/PAT the destination address??

robj by Community Member
  • 1828 Views
  • 6 replies
  • 0 Helpful votes

Hi Currently my Cisco IPS 4240 version 5.1(5) , is in Promiscous mode.Soon i will be configuring it in Inline mode .i will be using only 1 IPS Interface and will be configuring VLANs in the switch and connect the trunk port to the Gig0/0 of the IPS ....

Hello Our work purchase an ASA 5510 SEC. App. Firewall, which I have to set it up and connect it to my network at work for the purpose of publishing our corporate mail server (I am a new to Cisco routers and specialized in building AD infrastructure)...

smshahawi by Community Member
  • 732 Views
  • 2 replies
  • 0 Helpful votes

Hi allWe are trying to configure TFTP for Cisco PIX 6.3(4)PIX-515E ; however it is not taking the commands . Please let me know if it is possible to configure TFTP for this version or not . RegardsAnkur

What is multiple context on the ASA do?I have multiple customers that go into my ASA 5540 firewall to access certain resources/vlan on the internal network. Is multiple context applies to this scenario? Is this a best practice?thanks.

kope by Level 3
  • 1677 Views
  • 3 replies
  • 0 Helpful votes

we have Clean Access Manager Version: 4.1.2the policy is to check that the user has symantec antivirus on its machine , if not the NAC will redirect a link to the user to install the antivirus ,the main problem is that all the PCs joined the domain &...

Hi, the AAA server which is used for accounting, autharization and authendication. As per accounting it stores the information "what user's did do?" then can the same imformation keep the syslog server?? Thanks.

ray_stone by Level 7
  • 512 Views
  • 1 replies
  • 0 Helpful votes