Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

We have cat 6509 switch with FWSM, IDSM-2, NAM modules. Customer wants all the internal VLAN's to be monitored by IDSM in inline mode. Customer has around 400 VLANS in datacenter and wants to monitor all communications between VLAN's. How do I monito...

I can't seem to change the IP of the Inside Interface or the range of the DHCP server.When I try to change one or both I get this error:-----------------------[OK] hostname PIC506E[ERR]ip address inside 172.22.210.2 255.255.255.0 Interface address is...

ncschult2 by Level 1
  • 1545 Views
  • 5 replies
  • 0 Helpful votes

HI,I have an ASA 5520 with AIP-SSM10, I have configure AIP module with setup, but I dont have access through the ASDM to IPS, I only have access through cli session 1 comand.How can I acces the module through the ASDM.

We're configuring a firewall with 3 interfaces - inside, DMZ & outside and are trying to figure out what is the typical traffic flow for a firewall..Does the packet that enters from the outside, first goes out the DMZ interface, where the destination...

axfalk by Level 1
  • 1255 Views
  • 8 replies
  • 0 Helpful votes

I am a newbie to the Pix. I am trying to understand the running config list. The question I have is what does the command line mean:access-list inside-outbound deny tcp 10.1.2.0 255.255.255.0 any eq 135Does it mean deny TCP 135 traffic from outbound...

johnisccp by Level 1
  • 385 Views
  • 1 replies
  • 0 Helpful votes

dear guys help in pix 525 configurationi have pix525 with active /standby license what i have to doand right now i cant ping from my inside of pixfirewall to dmzzonei cant understandi appliend nat ,global,acces-list still its not pinging my secanrion...

Hello everyonePlease give me some help with the following.I'm trying to connect with a VPN Client which is behind a Checkpoint F/W to a CiscoPIX 515. Although the connection is established i cannot access the internal network behind the PIX. I config...

I'm moving from a Pix515e Failover set to an ASA5520 Failover set, and ending up with 2 less interfaces on the ASA. Is it a given that I should allocate 1 interface each for outside, inside, and failover - and then put all my DMZs on sub-interfaces o...

pd-yca by Level 1
  • 766 Views
  • 1 replies
  • 0 Helpful votes

Hi,I am trying to find out if I can configure an ASA 5510 to hold down 2 external WAN links for load balancing?If it could load balance itself it would be good or could I do something based on the inbound source IP's (i.e. ip's 192.168.20.1 to 20.100...

paul.adam by Level 1
  • 834 Views
  • 3 replies
  • 0 Helpful votes

Okay guys, here's the situation:I have three sites (sites A, B, and C). There is a site-to-site IPsec tunnel between PIXs from an internal LAN on site A (172.30.10.0 /24) to an internal LAN on site B (192.168.20.0 /24), and another tunnel from site ...

Hi I have Multiple branch offices connected with Headquarter with Via VPN tunnels using small routers.They are all connected to Cisco 3000 Concentrator. I want all sites to talk each other directly. What are my options?Thanks

shajay623 by Level 1
  • 388 Views
  • 1 replies
  • 0 Helpful votes