Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

How can I use Local SPAN with RSPAN ??I want to mirror traffics from ISP-A and ISP-B to Anomaly-detector module.so I had configured like this...C6500-A vlan 1000 name RSPAN remote-span! monitor session 10 source interface Gi5/1 - 2 rxmonitor session ...

creamware by Community Member
  • 814 Views
  • 1 replies
  • 0 Helpful votes

hi,i am facing a weird behavior from the ASA, i usually access my remote vpn to the office, and then can access via ssh the ASA inside interface to alter the configuration.since a week now , i can't access ASA this way, i checked the logs its giving ...

josephium by Level 3
  • 823 Views
  • 2 replies
  • 0 Helpful votes

I need to scrub (overwrite) the non-volatile memory of a PIX-506E for security purposes... anyone have any idea how to accomplish this? It's just a Flash EPROM, right? I've found a couple different commands for clearing flash, etc., but they all refe...

cboggs2007 by Community Member
  • 2830 Views
  • 6 replies
  • 0 Helpful votes

Hi:I need more DMZs than physical interfaces in my ASA 5520, so I configure subinterfaces and vlans. When I applied the failover config I saw in the subinterfaces a "Not-monitored" message and failover doesn't work if the physical interface is down.I...

Hello,I have a PIX501 at my house with the following setup:Motorola Cable Modem connect to my PIX 501.Pix 501 connected to my Linksys WRT350N wireless router.My XBOX360 connected wireless to my routerThe PIX is handing out IPs DHCP. The router is set...

Hi, I am trying to set up a Lan2Lan VPn between an ASA 5510 and a MS ISA Server 2004 machine. The configuration matches on both ends, but I get the following error in the ASA logs:113019: Group = x.x.x.x, Username = x.x.x.x, IP = x.x.x.x, Session dis...

Resolved! PIX OS 6.3 and QoS

Hi, all.As far as I know, Cisco IOS offers the ability (by default) to copy the IP ToS values from the packet header into the tunnel header when using an IPSec tunnel. But does the PIX software version 6.x do the same thing? I'd like to configure QoS...

saiiven07 by Level 2
  • 1155 Views
  • 2 replies
  • 0 Helpful votes

ALOHA -We re having two issues with Path Analysis that I was hoping someone may be able to help with -1) Our 6500 is being seen as an "end host". Anyway to correct this? It seems okay elsewhere.2) Our L2 hops are not being seen at all. They have been...

brobinson by Level 3
  • 478 Views
  • 1 replies
  • 0 Helpful votes

LMS

Can LMS give all informations about devices from different vendor based on MIB? Can I make a group of new class of devices based on it? Can it also give all characteristics of the link, like CIR, BECN, FECN etc? CAn it show the efficiency of QoS poli...

tmaksimovic by Community Member
  • 561 Views
  • 1 replies
  • 0 Helpful votes

Is there anyway to edit the order or remove items from being generated?This is from the help file. However, I am unable to find what is mentioned here.any help is greatly appreciated. Thanks.The Configuration view displays the status of all non-distr...

eaglesecure by Community Member
  • 1906 Views
  • 8 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card