Network Security

Hello All & Greetings.I have a scenario as below and would like how to make needed changes.I have a PIX firewall which is being used by 2 entities. However, one of them now wants togo their own separate way. I need to eliminate / remove all configs r...

I need to recovery the enable password on a couple of PIX firewalls running HSRP. Can anybody advise me if I need to adapt the standard recovery procedure? What I was considering was shutting both firwalls down, bring the primary one up, recovering...

Hi!I'm trying to configure simple multicast forwarding on PIX with client on the outside (IOS Router that pings 224.1.1.1) and server on the inside (IOS Router that joins 224.1.1.1), but it doesn't work. I see, that IGMP is working well, PIX proxy re...

Does anyone know how I might get jumbo (9000 bytes) frames thru my firewall? I need to transfer large data long distances, and jumbo frames are recommended. Can a PIX or FWSM do it?

The reseller who sold us this hardware claims that 3DES and VAC is included..anyone know:Is this true?How I trun on 3DES?thanks

I have an issue that i can not seem to see, i am trying to allow inside users access to the dmz, mainly for ftp and www. i know i am overlooking something simple. thanks in advanceHere is the portion of the config that i haveinterface ethernet0 100fu...

We have a site to site vpn running an ipsec tunnel with 3des encryption and a 155Mbps ATM link between the two (bridged with 3620 routers). The throughput and response times between the two sites is less than expected with intermittant periods of del...

I hvae a PIX 525, config as follows:no snmp-server locationno snmp-server contactsnmp-server community publicsnmp-server host dmz 192.192.192.10( my collecting server in DMZ zone,ip address is 192.192.192.10)no snmp-server enable trapsOID£º1.3.6.1.4....

We just bought the second concentrator 3000 and open up second ISP. I want to configurate the second to be the backup if first ISP fail all connect will be connected to the second concentrator. But my problem is not on vpn client, the problem is on h...

I was wondering if anyone could provide me with some inforamtion relevant to comparing router acls with pix acls.If I am splitting two internal private networks/subnets, and I want to protect them with ACL's, should I use a firewall with ACL's to do ...

Hi, I must set up this pix to replace another that is broken down. It worked like a failover, and I would like to know if this pix has the right license to do it.Many thanks inadvancepix# sh verCisco PIX Firewall Version 6.2(2)Cisco PIX Device Manage...

I am upgrading a failover set, two 535s from 6.1(4) to 6.3.3. My Secondary is licensed to run in failover secondary mode only. I concerned that if I take both devices down and disconnect the failover links the Secondary will become a toaster when i...

OK here is a scenario I am having trouble with. My desktop server was connected to our old Pix firewall and I was able to VPN into it. Since then we moved the desktop Server to the new PIX and changed the main gatewya to the New Pix and also had the...

We have several VPN 3.6 installed at clients with Windows XP (behind a DLink 804V), and they connect to a Cisco firewall PIX 501.After a short time (10-30 minutes) the connection terminates without any errormessages. (It can't be inactivity).Where ca...

Serial2/1 is up, line protocol is down Hardware is M4T Internet address is 10.0.0.1/30 MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, reliability 128/255, txload 1/255, rxload 1/255 Encapsulation HDLC, crc 16, loopback not set Keepalive set (...