Network Security

Engage with peers and experts on network security topics such as FTD, FMC, FDM, CDO and ASA.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Hi all.My Customer has a Pix running PIX Version 5.2(9) and cannot upgrade the software because a Token Ring interface on the firewall is needed.Given that the "show cpu usage" command is not available on that software release, how can I calculate an...

m.laporta by Level 1
  • 519 Views
  • 2 replies
  • 0 Helpful votes

On PIX515 with a DMZ port running 5.2(9) everything is working as far as traffic flow in and out of the proper interfaces. I am upgrading to, or rather attempting to, 6.2(2) in order to evaluate N2H2 content filtering. 6.2(2) is required in order t...

is by Level 1
  • 443 Views
  • 1 replies
  • 0 Helpful votes

In my network I have a PIX-520 with 2 interfaces ( i,e inside and outside ) I am using real ip's on the inside means using them without NAT. I want my traffic generated from Inside should go to internet via router placed on the outside interface of P...

ranairfan by Level 1
  • 525 Views
  • 1 replies
  • 0 Helpful votes

I have a PIX 506E firewall, this device have only two ethernet interface : one for the lan and the other one for the internet. I would like to add a third interface on the PIX without having to change my PIX. So my question is : can I configure a sub...

kayih by Level 1
  • 760 Views
  • 1 replies
  • 0 Helpful votes

I have just recently taken over our PIX firewall and have been experimenting with the logging features. I am currently logging up to Warning Level, and have seen a lot of activity that leads me to believe that several people have attempted to get pa...

bbeck by Level 1
  • 615 Views
  • 3 replies
  • 0 Helpful votes

Is it possible to have a one global IP address to be statically mapped to two separate IP adresses (one of them on the inside and one on the DMZ) by specifying the requested port? I know that you can map multiple global IP addresses to a single inter...

tvorhauer by Level 1
  • 885 Views
  • 4 replies
  • 0 Helpful votes

I am attempting to configure a PIX 520 to support connections from a low security zone to high security zone inbound to a exchange server from outlook. I am using the NAT 0 options and have the no problem pinging, hitting the web interface on the sa...

dana by Level 1
  • 581 Views
  • 3 replies
  • 0 Helpful votes

Hi,This is the spec of our PIX:Cisco PIX Firewall Version 6.2(2)Cisco PIX Device Manager Version 2.0(2)Compiled on Fri 07-Jun-02 17:49 by morleeFIREWALL up - days - hoursHardware: PIX-515, 32 MB RAM, CPU Pentium 200 MHzFlash i28F640J5 @ 0x300, 16MB...

alitster by Level 1
  • 568 Views
  • 1 replies
  • 0 Helpful votes

What is the best way to disable NAT on the PIX (specifically between two interface, not globally)? There appears to be two alternatives: use a net static of the form "static(high,low) high high" or "nat 0 (high) access-list". I've seen postings which...

I have CiscoWorks 2000 LMS / RWAN with the VPN Monitor software loaded. Currently I have our VPN 3000 concentrators entered in RME with only an SNMP Read-Only string. If I add a telnet access into RME for the VPN concentrator will it pull a copy of t...

thethmon by Level 1
  • 1295 Views
  • 3 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card